140ERT85410 多功能输入模块 125 V

【产品详情】

按照设备文档中建议的所有启动测试进行操作。存放所有设备

供将来参考的文档。

软件测试必须在模拟和真实环境中进行。

确认完整的系统没有任何短路和临时接地

根据当地法规安装(根据美国国家电气规范，对于

实例)。如果需要进行高电压测试，请按照设备上的建议进行

防止设备意外损坏的文件。

设备通电前:

清除设备上的工具、仪表和杂物。

请关闭设备机框门。

移除输入电源线上的所有临时接地。

执行制造商推荐的所有启动测试。

警告

设备操作危害

确认所有安装和设置过程已经完成。

在执行操作测试之前，移除所有阻塞或其他临时保持手段

用于所有组件设备的装运。

清除设备上的工具、仪表和杂物。

不遵守这些说明可能会导致死亡、严重伤害或设备损坏。

8 33002499 12/2018

操作与调整

以下注意事项来自NEMA标准出版物ICS 7.1-1995(英文)

版本为准):

无论在设计和制造设备或在选择时是否谨慎

和组件的额定值，有可能遇到的危险，如果这样的设备

不当操作。

有时设备可能调整不当，从而产生不满意或不安全的产品

操作。始终使用制造商的说明作为功能调整的指导。

使用这些调节装置的人员应熟悉设备

制造商的说明书和与电气设备配套使用的机械。

只有操作人员实际需要的操作调整才能访问

操作员。应限制对其他控件的访问，以防止未经授权的更改

操作特征

140ERT85410 多功能输入模块 125 V

【英文介绍】

Follow all start-up tests recommended in the equipment documentation. Store all equipment 

documentation for future references.

Software testing must be done in both simulated and real environments.

Verify that the completed system is free from all short circuits and temporary grounds that are not 

installed according to local regulations (according to the National Electrical Code in the U.S.A, for 

instance). If high-potential voltage testing is necessary, follow recommendations in equipment 

documentation to prevent accidental equipment damage.

Before energizing equipment:

 Remove tools, meters, and debris from equipment.

 Close the equipment enclosure door.

 Remove all temporary grounds from incoming power lines.

 Perform all start-up tests recommended by the manufacturer.

WARNING

EQUIPMENT OPERATION HAZARD

 Verify that all installation and set up procedures have been completed.

 Before operational tests are performed, remove all blocks or other temporary holding means 

used for shipment from all component devices.

 Remove tools, meters, and debris from equipment.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

8 33002499 12/2018

OPERATION AND ADJUSTMENTS

The following precautions are from the NEMA Standards Publication ICS 7.1-1995 (English 

version prevails):

 Regardless of the care exercised in the design and manufacture of equipment or in the selection 

and ratings of components, there are hazards that can be encountered if such equipment is 

improperly operated.

 It is sometimes possible to misadjust the equipment and thus produce unsatisfactory or unsafe 

operation. Always use the manufacturer’s instructions as a guide for functional adjustments. 

Personnel who have access to these adjustments should be familiar with the equipment 

manufacturer’s instructions and the machinery used with the electrical equipment.

 Only those operational adjustments actually required by the operator should be accessible to 

the operator. Access to other controls should be restricted to prevent unauthorized changes in 

operating characteristics

140ERT85410 多功能输入模块 125 V

【其他型号推荐】