PM3398B-6-1-3-E 模拟量输入模块

【产品详情】

plc数字量和模拟量输入模块的区别是什么？一般来说我们把模拟量模块分为三种的:一是模拟量输入模块、二是模拟量输出模块、三是模拟量输入/输出模块。那数字量输入模块跟模拟量输入模块有什么区别呢？

一：PLC模拟量输入模块(模拟量输入模块)又称A/D模块，将现场由传感器检测而产生的连续的模拟量信号转换成PLC的CPU可以接收的数字量，一般多为12位二进制数，数字量位数越多的模块，分辨率就越高。

二：PLC模拟量输出模块。模拟量输出模块又称为D/A模块，把PLC的CPU送往模拟量输出模块的数字量转换成外部设备可以接收的模拟量（电压或电流）。模拟量输出模块所接收的数字信号一般多为12位二进制数，数字量位数越多的模块，分辨率就越高。而数字量模块就是检测外部开关量输入的状态。

plc数据采集网关

三：数字量输入输出信号就是开关量信号，0或者1，模拟量信号，有2种，电压或者电流信号 ，一般是变送器传过来的信号，比如用压力变器检测水管压力，它会输出一个模拟信号4-20ma 或者 0-10V的信号给PLC，PLC来进行数据处理，这便是数字量输入模块跟模拟量输入模块的区别了。

在输入采样阶段，PLC以扫描方式依次地读入所有输入状态和数据，并将它们存入I/O映象区中的相应得单元内。输入采样结束后，转入用户程序执行和输出刷新阶段。在这两个阶段中，即使输入状态和数据发生变化，I/O映象区中的相应单元的状态和数据也不会改变。因此，如果输入是脉冲信号，则该脉冲信号的宽度必须大于一个扫描周期，才能保证在任何情况下，该输入均能被读入。

PM3398B-6-1-3-E 模拟量输入模块

【英文介绍】

What is the difference between plc digital and analog input modules? Generally speaking, we divide the analog module into three types: one is the analog input module, the other is the analog output module, and the third is the analog input/output module. What is the difference between a digital input module and an analog input module?

One: PLC analog input module (analog input module), also known as A/D module, converts the continuous analog signal generated by the sensor detection in the field into the digital quantity that the PLC CPU can receive, generally 12-bit binary number, the more digital quantity modules, the higher the resolution.

Two: PLC analog output module. The analog output module, also known as D/A module, converts the digital quantity sent by the PLC CPU to the analog output module into the analog quantity (voltage or current) that can be received by the external device. The digital signal received by the analog output module is generally 12-bit binary number, and the more digital quantity modules, the higher the resolution. The digital module is to detect the state of the external switching input.

plc data acquisition gateway

Three: Digital input and output signal is the switching signal, 0 or 1, analog signal, there are two, voltage or current signal, generally the signal transmitted by the transmitter, such as the pressure transformer to detect the pressure of the water pipe, it will output an analog signal 4-20ma or 0-10V signal to the PLC, PLC for data processing, This is the difference between a digital input module and an analog input module.

In the input sampling phase, the PLC successively reads all input status and data by scanning and stores them in the corresponding cell in the I/O image area. After the end of the input sampling, the user program execution and output refresh phase. In both phases, even if the input state and data change, the state and data of the corresponding unit in the I/O map area will not change. Therefore, if the input is a pulse signal, the width of the pulse signal must be greater than one scan cycle to ensure that the input can be read in any case.

PM3398B-6-1-3-E 模拟量输入模块

【其他型号推荐】