VE3004 AMS设备管理器

【产品详情】

特征

不间断控制操作

可在线升级

自动调试

无扰动过渡

使用带有DeltaV系统的AMS设备管理器，您可以访问重要的HART、基金会现场总线、WirelessHART和Profibus

无需额外布线或现场布线的DP设备数据！

为该设备提供现场电源，或在现场端子或作为总线的现场电源通过载体，在拆卸或拆卸前必须拆卸连接设备。此单元可在系统运行时拆卸或插入电源在下列情况下通电:(注意一次只能拆卸一个单元系统电源通电。)

•与KJ1501X1-BC1系统双机配套使用时运行在24 VDC或12 VDC输入电源。一次电路布线输入功率的电感必须小于23或者是经过认证的开路电源电压，Ui为12.6 VDC, Lo小于23uh(包括导线电感)。

•非火花场电路在拆卸和插入之前必须断电产品。旋转键控系统确保兼容性在I/O卡和终端阻塞之间安装完成。接线盒必须是否为I/O卡设置了键被使用。

为该设备提供现场电源，或在现场端子或作为总线的现场电源通过载体，在拆卸或拆卸前必须拆卸连接设备。必须完成所有I/O循环评估能量有限的节点。此单元可在系统运行时拆卸或插入电源在下列情况下通电:(注意一次只能拆卸一个单元系统电源通电。)

•与KJ1501X1-BC1系统双机配套使用时运行在24 VDC或12 VDC输入电源。一次电路布线输入功率的电感必须小于23或者是经过认证的开路电源电压，Ui为12.6 VDC, Lo小于23uh(包括导线电感)。旋转键控系统确保兼容性在I/O卡和终端阻塞之间安装完成。接线盒必须是否为I/O卡设置了键被使用。不能用端子座熔断器拆卸无火花电路的场电源通电。

VE3004 AMS设备管理器

【英文介绍】

trait

Uninterrupted control operation

Online upgradable

Automatic debugging

Undisturbed transition

With AMS Device Manager with DeltaV system, you can access the important HART, Foundation Fieldbus, WirelessHART and Profibus

DP device data without additional wiring or field wiring!

The field power supply for the device, or the field power supply passing through the carrier at the field terminal or as a bus, must be removed before disassembly or disassembly. This unit can be removed or plugged into the power supply while the system is running in the following cases :(Note that only one unit can be removed at a time to power the system power supply.)

• When used with the KJ1501X1-BC1 system, it runs at 24 VDC or 12 VDC input power. The inductance of the primary circuit routing input power must be less than 23 or a certified open supply voltage with a Ui of 12.6 VDC and Lo less than 23uh(including wire inductance).

• Non-spark field circuits must power off the product before disassembly and insertion. The rotary keying system ensures compatibility between the I/O card and terminal blocking installation is complete. The junction box must be used if the key is set for the I/O card.

The field power supply for the device, or the field power supply passing through the carrier at the field terminal or as a bus, must be removed before disassembly or disassembly. All I/O cycles must be completed to evaluate nodes with limited energy. This unit can be removed or plugged into the power supply while the system is running in the following cases :(Note that only one unit can be removed at a time to power the system power supply.)

• When used with the KJ1501X1-BC1 system, it runs at 24 VDC or 12 VDC input power. The inductance of the primary circuit routing input power must be less than 23 or a certified open supply voltage with a Ui of 12.6 VDC and Lo less than 23uh(including wire inductance). The rotary keying system ensures compatibility between the I/O card and terminal blocking installation is complete. The junction box must be used if the key is set for the I/O card. Do not use the terminal block fuse to disassemble the field power supply of the non-spark circuit.

VE3004 AMS设备管理器

【其他型号推荐】