HONEYWELLCC-PCNT02控制器模块

【产品详情】

HONEYWELL CC-PCNT02维护内部历史记录（事件日志），最多200个事件（火灾、故障、重置等）。

HONEYWELL CC-PCNT02霍尼韦尔C300控制器模块

HONEYWELL CC-PCNT02报警面板通常是一个具有适当和固定程序的自动装置。该程序允许您进行许多简单的设置，如输入延迟、NO或NC触点方向等。该计划是制造商在这一活动领域的经验的结果，最重要的是积累了其客户的所有具体要求。因此，当制造商能够改进其产品时，安全的保证当然是该制造商存在的时间长度。

报警管理由基本程序执行，不能修改。只有配置是可能的。一个警报面板迅速运转。它的程序包括在内，只需连接电源和至少一个输入。“自动化”解决方案需要创建一个程序，这可能需要几个月的时间才能完成，其中存在异常风险，而这些异常将在很久以后才被发现。另一方面，报警面板通常具有较高的干扰容限(电源电压通常高于+/-30%，交流/DC电源)。向报警面板添加通道很快。只需连接一个输入触点并修改设置。没有经验的技术人员也能做到这一点。

这个可以使用带有至少486型PC和适当的PC软件。安装支架位置a、探测器具有120度锥形视野（视角）。建议探测器位于主要火灾威胁位置探测器视野的轴。由于探测器必须“看到”火灾才能探测到它，它应该安装在角落和天花板等位置避免视线堵塞。b、选择将固定探测器与外壳材料类型保持一致地方例如，可以在安装支架，并用螺钉、铆钉等固定。如果安装面为聚丙烯，可进行热焊接用于固定支架。c、将外壳滑到安装支架上，直到它锁定到位。将每个“引线”连接到适当的连接上外部设备。接线见第6节表1细节。小心：在处理探测器的引线。正确使用腕带接地将有助于防止产品损坏。

CC-PCNT02控制构建器提供了一个图形工程环境，工程师可以在其中配置Experion系统，并通过使用库中可用的各种功能块创建控制策略。基于C300 CEE的控制策略可以配置为具有50毫秒的最小执行速率。

TC/RTD IOM支持PV交付前打开传感器检测的配置参数。在OTD配置激活的情况下，PV被采样并保持，同时在同一测量窗口内执行OTD循环。如果OTD为负，则PV通过系统向上传播。

如果OTD为正，则PV设置为NAN，并设置输入通道软故障。通过这种方式，对于由于热电偶开路而无效的PV值，不会发生不适当的控制动作。PV采样/报告不会因OTD处理而增加延迟。

HONEYWELLCC-PCNT02控制器模块

HONEYWELL CC-PCNT02 maintains internal history (event log) for up to 200 events (fire, failure, reset, etc.).

HONEYWELL CC-PCNT02 Honeywell C300 controller module

The HONEYWELL CC-PCNT02 alarm panel is typically an automatic device with proper and fixed procedures. The program allows you to make many simple Settings such as input delay, NO or NC contact direction, etc. The program is the result of the manufacturer's experience in this field of activity and, above all, the accumulation of all the specific requirements of its customers. Therefore, when a manufacturer is able to improve its products, the guarantee of safety is of course the length of time that the manufacturer exists.

Alarm management is performed by basic procedures and cannot be modified. Only configuration is possible. An alarm panel swung into action. Its program is included, just connect the power supply and at least one input. "Automated" solutions require the creation of a program, which can take months to complete, with the risk of anomalies that will not be discovered until much later. On the other hand, alarm panels usually have a high interference tolerance (supply voltage is usually higher than +/-30%, AC /DC supply). Adding a channel to the alarm panel is fast. Simply connect an input contact and modify the Settings. Inexperienced technicians can do this.

This can be used with at least a type 486 PC and appropriate PC software. The detector has a 120-degree conical field of view (Angle of view). It is recommended that the detector be located on the axis of the detector field of view at the primary fire threat location. Since the detector must "see" the fire in order to detect it, it should be installed in places such as corners and ceilings to avoid blocking the line of sight. B. Select the place where the fixed detector is consistent with the material type of the housing. For example, you can install the bracket and fix it with screws, rivets, etc. If the mounting surface is polypropylene, it can be thermally welded for fixing the bracket. c. Slide the housing onto the mounting bracket until it locks into place. Connect each "lead" to the appropriate connected external device. The wiring is detailed in Table 1, Section 6. Caution: In handling detector leads. Proper use of wrist strap grounding will help prevent product damage.

The CC-PCNT02 control builder provides a graphical engineering environment where engineers can configure Experion systems and create control policies by using various functional blocks available in the library. C300 CEE-based control policies can be configured to have a minimum execution rate of 50 milliseconds.

TC/RTD IOM supports configuration parameters for sensor detection to be turned on before PV delivery. With the OTD configuration active, the PV is sampled and held while the OTD cycle is performed within the same measurement window. If OTD is negative, PV propagates upward through the system.

If OTD is positive, PV is set to NAN and input channel soft failure is set. In this way, no improper control action can occur for PV values that are invalid due to the thermocouple's open circuit. PV sampling/reporting does not add latency due to OTD processing.

HONEYWELLCC-PCNT02控制器模块

【常见问题】

无论您对库存，价格，故障排除还是其他方面有任何疑问，我们都能满足您的需求。请致电我们，填写我们的表格，或向我们发送电子邮件-任何适合您的方式。期待您的回音！

问：您的交货时间如何？

答：我们有很多库存商品，3-5天您将收到它。

问：你们提供保修吗？

答：是的，我们为所有剩余的部件提供1年保修。

问：您可以接受哪些付款方式？

答：通常我们在中国大陆接受T/T和人民币转账