HONEYWELLCC-TCF901   驱动模块

HONEYWELLCC-TCF901   驱动模块用于激励电磁铁

品牌:Honeywell

型号 ：CC-TCF901

产品描述

HONEYWELLCC-TCF901   驱动模块用于激励电磁铁，电磁铁将电枢拉向它。电枢与电路的另一端接触，从而接通电路并允许电流流动。当电磁铁停止工作时，附在衔铁上的弹簧将电磁铁拉回，切断电流。由于具有独立控制信号的特点，早期的计算机大量使用继电器来形成逻辑电路，如哈佛马克2号、ARRA、Zuse Z2和Zuse Z3。它们还被广泛用作早期电话系统(如史端乔和纵横制电话交换系统)中复杂交换的逻辑控制。

HONEYWELLCC-TCF901   驱动模块通过允许更大的电流流动来打开设备继电器是一种电动或机电开关，由电磁铁、衔铁、弹簧和一-组电触点组成。电磁开关由小电流操作，通过释放或缩回衔铁触点来接通或切断大电流，从而切断或接通电路。当受控电路和控制电路之间必须有电气隔离时，或者当多个电路需要由单个信号控制时，继电器是必要的。继电器是一个电磁开关;因此，它的心脏是电磁体，由小电流供电，充当杠杆或开关本身。这使得允许相对小的电流影响和控制大得多的电流成为可能。传感器是敏感的设备,它们只产生少量的电流，但为了让传感器驱动更大的设备，它需要某种东西通过允许更大的电流流动来打开设备。样，传感器可以作为继电器的控制输入，当它被激活时，更大的电流流向设备。例如，可以分配光或光传感器来控制室外的灯，以便当外面变暗时，光传感器激活充当灯开关的继电器。

HONEYWELLCC-TCF901   驱动输出

Brand :Honeywell

Model: CC-TCF901

Product description

The HONEYWELL CC-TCF901 drive module is used to excite the electromagnet, which pulls the armature towards it. The armature makes contact with the other end of the circuit, thus closing the circuit and allowing the current to flow. When the electromagnet stops working, a spring attached to the armature pulls the electromagnet back, cutting off the current. Due to the characteristic of independent control signals, early computers made extensive use of relays to form logic circuits, such as the Harvard Mark 2, ARRA, Zuse Z2, and Zuse Z3. They were also widely used as logical controls for complex exchanges in early telephone systems such as Strowger and Crossbar telephone switching systems.

HONEYWELL CC-TCF901 Drive module Turns on equipment by allowing greater current flow A relay is an electric or electromechanical switch consisting of an electromagnet, armature, spring, and a set of electrical contacts. The electromagnetic switch is operated by a small current, and a large current is switched on or off by releasing or retracting the armature contact, thus cutting or closing the circuit. Relays are necessary when there must be electrical isolation between the controlled circuit and the control circuit, or when multiple circuits need to be controlled by a single signal. The relay is an electromagnetic switch; Thus, its heart is the electromagnet, powered by a small current that acts as a lever or the switch itself. This makes it possible to allow relatively small currents to influence and control much larger currents. Sensors are sensitive devices, and they only produce a small amount of current, but in order for a sensor to drive a larger device, it needs something to turn the device on by allowing a larger flow of current. Like, the sensor can act as a control input to the relay, and when it is activated, a greater current flows to the device. For example, light or light sensors can be assigned to control lights outside so that when it gets dark outside, the light sensor activates a relay that acts as a light switch.

HONEYWELLCC-TCF901   驱动输出