WOODWARD 5466-1141 数字控制器 安全应用模块 

【产品详情】

CPU5200SA（安全应用）模块 5466-1141 被认为是 MicroNet 数字控制器系列中的较新模块，作为 MicroNet-Plus 单元。此模块可用于 MicroNet 8 或 14 VME 插槽机箱。

单元 5466-1141 是一个 CPU5200SA（安全应用）模块，作为 MicroNet 数字控制器的一部分生产。该装置可用于单工或冗余或 I/O 模块，请注意，如果控制器用于冗余系统，则需要两个 CPU 模块才能正常工作。两个 CPU 将运行相同的应用程序，并从 VME 背板上的相同引脚接收电源，并且由于可以访问不同的 I/O 模块，因此可以在同一 VME 总线上使用。两个所需 CPU 的位置将位于 A1 和 A8/A14 插槽中，这些插槽是相应机箱的第一个和最后一个插槽。

根据 26166V2 手册中列出的 MicroNet 系列单元的表格，5466-1141 模块被标记为较新的状态模块。该模块将用于MicroNet Plus机箱，无论系统配置是单工配置，全冗余还是部分冗余配置，本机都将配置在MicroNet Plus机箱的主机架中。

5466-1141 型号可用于柴油/燃气发动机涡轮机或水力/蒸汽/燃气轮机应用。该单元还需要使用伍德沃德的图形应用程序（GAP）来正确操作模块。 有一个 <> 秒的窗口，将在两个 CPU 都通电后运行它们。第一个要运行的 CPU 将移除看门狗 LED 并成为系统管理员。请注意，可以在设备上执行诊断测试，该测试将在第一个和第二个CPU之间切换syscon应用程序三次，然后再继续。

WOODWARD 5466-1141 数字控制器 安全应用模块 

【英文介绍】

The CPU5200SA (Security Applications) module 5466-1141 is considered a relatively new module in the MicroNet family of digital controllers as a MicronET-Plus unit. This module can be used in MicroNet 8 or 14 VME slot cases.

Unit 5466-1141 is a CPU5200SA (Security Applications) module manufactured as part of the MicroNet digital Controller. The device can be used in simplex or redundant or I/O modules, note that if the controller is used in a redundant system, two CPU modules are required to function properly. Both cpus will run the same applications and receive power from the same pins on the VME backplane, and can be used on the same VME bus because they have access to different I/O modules. The locations for the two required cpus will be in the A1 and A8/A14 slots, which are the first and last slots in the respective chassis.

Modules 5466-1141 are labeled as newer status modules according to the table of MicroNet series units listed in the manual 26166V2. The module will be used in the MicroNet Plus chassis and the unit will be configured in the host rack of the MicroNet Plus chassis regardless of whether the system configuration is simplex, fully redundant or partially redundant.

Models 5466-1141 can be used in diesel/gas engine turbines or hydraulic/steam/gas turbine applications. The unit also requires the use of Woodward's Graphics Application (GAP) to properly operate the module. There is a <> second window that will run both cpus after they are powered on. The first CPU to run will remove the watchdog LED and become the system administrator. Note that you can perform a diagnostic test on the device that will switch the syscon application three times between the first and second CPU before continuing.

WOODWARD 5466-1141 数字控制器 安全应用模块 

【其他型号推荐】