9905-151 电子负载分配和速度控制 原动机
【产品详情】
该特殊型号是反向作用的高压型号,执行器电流为0-200 mA。该型号的速度设置输入为 1-5 Vdc。 控制和原动机的操作取决于控制的正确安装,安装时甚至在安装控制之前,请确保没有对控制发生损坏,以任何方式损坏; 机箱上的凹痕、端子断裂或弯曲、端子螺钉断裂、丢失或弯曲会影响此控件的工作方式, 损坏将导致控制器和原动机之间出现故障。
请注意,当使用控制器并将增益电位计调到最大容量时,这可能不是必需的,由于稳定性条件范围很广,可能需要调整增益电位器以纠正和补偿不稳定性。
如果您已执行调整,其中已将下降设置为针对实用程序,如果在关闭断路器后负载开始迅速浪涌,请立即关闭设备。您应始终缓慢调整电位计,以免使设备扭矩过大。
如果在操作控制器和原动机时,控制器上的速度设置没有正确调节速度,请检查电位器是否出现故障,首先检查电位器是否有故障,然后更换为跳线并用主电位器设置速度。
9905-151 电子负载分配和速度控制 原动机
【英文介绍】
Woodward Part 9905-151 Series 2301A Load distribution and speed control. The operating current is 0-200 mA and the speed setting input is 1-5 VDC.
This particular model is a reverse-acting high-voltage model with an actuator current of 0-200 mA. The speed setting input for this model is 1-5 Vdc. The operation of the control and prime mover depends on the correct installation of the control, and during installation, even before the installation of the control, please ensure that there is no damage to the control, in any way; Dents in the chassis, broken or bent terminals, broken, lost or bent terminal screws affect the way this control works, and damage will cause a failure between the controller and the prime mover.
Note that this may not be necessary when using the controller and setting the gain potentiometer to its maximum capacity, as the gain potentiometer may need to be adjusted to correct and compensate for instability due to a wide range of stability conditions.
If you have performed an adjustment where the drop has been set to the utility, turn off the device immediately if the load begins to surge rapidly after the circuit breaker is turned off. You should always adjust the potentiometer slowly so as not to torque the device too much.
If the speed setting on the controller does not adjust the speed correctly when operating the controller and prime mover, check whether the potentiometer is faulty, first check whether the potentiometer is faulty, and then replace it with a jumper and set the speed with the main potentiometer.
9905-151 电子负载分配和速度控制 原动机
【其他型号推荐】
PR6426/010-020 | EPRO | 前置器及传感器 | BENTLY 3308812800165070 | 环路数据处理模件 | Bently Nevada |
PR6426/010-010 | EPRO | 前置器及传感器 | BENTLY 330878-90-00 | 计算机接口模件 | Bently Nevada |
PR6426/010-000 | EPRO | 前置器及传感器 | BENTLY 330877803700 | DCS板 | Bently Nevada |
PR6426/000-141 | EPRO | 前置器及传感器 | BENTLY 33087601100100 | 可编程控制系统 | Bently Nevada |
PR6426/000-140 | EPRO | 前置器及传感器 | BENTLY 330854-080-24-05 | ABBIGBT模块 | Bently Nevada |
PR6426/000-130 | EPRO | 前置器及传感器 | BENTLY 3308510500271000 | 模件总线电缆适配器接口 | Bently Nevada |
PR6426/000-121 | EPRO | 前置器及传感器 | BENTLY 330851-04-000-023-10-01-05 | 模件总线连接电缆 | Bently Nevada |
PR6426/000-111 | EPRO | 前置器及传感器 | BENTLY 330851-02-000-070-50-00-05 | 诊断电缆 | Bently Nevada |
PR6426/000-101 | EPRO | 前置器及传感器 | BENTLY 330850-90-05 | 按键屏 | Bently Nevada |
PR6426/000-100 | EPRO | 前置器及传感器 | BENTLY 330850-90-00 | 红外通讯 | Bently Nevada |
PR6426/000-041 | EPRO | 前置器及传感器 | BENTLY 330850-51-05 | S型热电偶 | Bently Nevada |
PR6426/000-031 | EPRO | 前置器及传感器 | BENTLY 330850-50-CN | 端口号 | Bently Nevada |
PR6426/000-030 | EPRO | 前置器及传感器 | BENTLY 33080-51-00 | 模拟输入输出 | Bently Nevada |
PR6426/000-021 | EPRO | 前置器及传感器 | BENTLY 3308012806095030 | 缓冲板 | Bently Nevada |
PR6426/000-020 | EPRO | 前置器及传感器 | BENTLY 3308012805145030 | 直流调速器主控制cpu板 | Bently Nevada |
PR6426/000-010 | EPRO | 前置器及传感器 | BENTLY 3308012804130030 | 输入模块横河卡件 | Bently Nevada |