9905-132 标准速度控制器 速度控制系列

【产品详情】

9905-132 模块是一种前向式标准速度控制器，可在 8-131 V 交流或 90-150 Vdc 下运行，来自伍德沃德的 2301A 负载分配和速度控制系列。该型号可与燃气轮机或蒸汽轮机原动机一起使用。

9905-132 装置是 2301A 电子负载分配和速度控制，提供伍德沃德制造的低压或高压型号。该型号被设计为标准速度控制。两种电压型号通常由 90-150 Vdc 或 85-132 Vac 的电源（高压）和 20-40 Vdc 的低压型号供电，具体取决于所使用的模块类型。电源线通过第十五个端子（负极）和第十六个端子（正极）从电源连接到控制器。引线必须通过相应的正极和负极引线连接到 9905-132 上的匹配端子。电源 9905-132 Vdc 应严格专用于调速器。

用于电流互感器校正的临时负担接线端子必须通过端子四至九连接;如果不使用此电阻器，则需要关闭发动机，并且还必须卸下负载。

9905-132 控制器提供速度微调，具体取决于安装，无论是分轴还是尾轴;在分体轴安装上，只需在尾轴调速器上转动速度微调电位器;如果需要，配平也可以安装在发动机调速器上，并完全顺时针运行以进行标准操作。

9905-132 装置可与负载传感器一起使用。当该装置与负载传感器一起使用时，只要与两个或多个系统并联使用，系统就会与系统中的其他发电机共享收集的负载。当 9905-132 用于其预期目的时，它将保持和监控原动机的速度，以确保其在设定的操作水平上使用。

9905-132 标准速度控制器 速度控制系列

【英文介绍】

The 9905-132 module is a forward-facing standard speed controller that operates at 8-131 V AC or 90-150 Vdc from Woodward's 2301A load distribution and speed control family. This model can be used with a gas or steam turbine prime mover.

The 9905-132 unit is a 2301A electronic load distribution and speed control, available in low or high voltage models manufactured by Woodward. This model is designed with standard speed control. Both voltage models are typically powered by a 90-150 Vdc or 85-132 Vac power supply (high voltage) and a 20-40 Vdc low voltage model, depending on the type of module used. The power cable is connected from the power supply to the controller through the fifteenth terminal (negative) and sixteenth terminal (positive). The leads must be connected to the matching terminals on the 9905-132 via the corresponding positive and negative leads. Power supply 9905-132 Vdc should be strictly dedicated to the governor.

Temporary load terminals for current transformer calibration must be connected through terminals 4 to 9; If this resistor is not used, the engine needs to be turned off and the load must also be removed.

The 9905-132 controller provides speed fine-tuning, depending on the installation, whether it is a split shaft or a stern shaft; On the split shaft installation, just rotate the speed fine-tuning potentiometer on the tail shaft governor; If required, the trim can also be mounted on the engine governor and run fully clockwise for standard operation.

The 9905-132 unit can be used with a load sensor. When the device is used with a load sensor, as long as it is used in parallel with two or more systems, the system shares the collected load with other generators in the system. When the 9905-132 is used for its intended purpose, it will maintain and monitor the speed of the prime mover to ensure that it is used at the set level of operation.

9905-132 标准速度控制器 速度控制系列

【其他型号推荐】