9905-021 负载分配输入 WOODWARD

【产品详情】

型号 9905-021 2301A 系列负载分配和速度控制。0-6 VDC 的负载分配输入，可与蒸汽轮机或燃气发动机一起使用。

Woodward 2301A 系列 9905-021 控制器是一种反向作用的低压型号，执行器电流为 0-200 mA。该型号也是单独的执行器型号，不提供减速斜坡。当将本机连接到 20-40 Vdc 端子 <> 和 <> 的电源存储时，负极引线连接到端子 <>，正极引线连接到端子 <>。

负载分配线连接到端子0和6，负载信号引线连接到端子<>和<>。第十一个端子在负载分配和负载信号功能之间共享，第十一个端子是负极连接器，而端子十和十二是正极连接器。该型号的负载分配输入指定为 <>-<> Vdc。

连接屏蔽线时，需要从两端去除屏蔽上的外部绝缘层，这会暴露盘绕屏蔽层;盾牌永远不应该被切断。

在使用控制器之前，建议目视检查模型，确保检查螺钉是否完好无损，没有损坏或破裂的端子，并检查所有表盘以确保没有以任何方式损坏或损坏，因为这可能会妨碍设备的性能。如果发现控制器有任何损坏，请联系AX控制器以询问是否可以修复控制器。

安装控件时，请确保保护控件免受水或冷凝的影响，如果控件获得任何水分，则可能导致模型出现故障并阻止模型执行。

9905-021 负载分配输入 WOODWARD

【英文介绍】

Model 9905-021 2301A Series Load distribution and speed control. Load distribution inputs of 0-6 VDC for use with steam turbines or gas engines.

The Woodward 2301A Series 9905-021 controller is a reverse-acting low-voltage model with an actuator current of 0-200 mA. This model is also a separate actuator number and does not provide a deceleration ramp. When connecting the unit to the power storage of the 20-40 Vdc terminals <> and <>, the negative lead is connected to the terminal <> and the positive lead is connected to the terminal <>.

The load distribution wires are connected to terminals 0 and 6, and the load signal leads are connected to terminals <> and <>. The eleventh terminal is shared between the load distribution and load signal functions, and the eleventh terminal is the negative connector, while terminals ten and twelve are the positive connector. The load distribution input for this model is specified as <>-<> Vdc.

When connecting the shield wire, the external insulation layer on the shield needs to be removed from both ends, which will expose the coiling shield. The shield should never be cut.

Before using the controller, it is recommended to visually inspect the model to ensure that the inspection screws are intact, there are no damaged or cracked terminals, and to inspect all dial faces to ensure that they are not damaged or damaged in any way, as this could hinder the performance of the device. If you find any damage to the controller, contact the AX controller to ask if you can repair the controller.

When installing the control, be sure to protect the control from water or condensation, if the control gets any moisture, it can cause the model to malfunction and prevent the model from executing.

9905-021 负载分配输入 WOODWARD

【其他型号推荐】