IC670MDL740 正逻辑分立输出模块 通用输出模块

【产品详情】

该IC670MDL740是由GE Fanuc制造的正逻辑分立输出模块。该模块是通用输出模块，安装在总线接口单元 （BIU） 上，用于实现扩展 I/O 解决方案。它通常用于通电输出设备，例如指示灯、继电器线圈、螺线管驱动设备和具有低额定电流的类似设备，因为该IC670MDL740在电压输出范围为 0-5 VDC 和标称电压为 4 VDC 时提供每通道 10.30 安培的输出电流和每个模块总共 24 安培的输出电流。

IC670MDL740设计有单独的状态 LED 指示灯，指示模块每个输出通道的开/关状态。整个 I/O 组安装有一个公共保险丝，该保险丝还分配了一个 LED 指示灯，用于描述保险丝熔断状态。该模块产生额定 2 安培的浪涌电流，最大持续时间为 100 ms。输出通道的最小负载电流为每点 1 mA，输出压降为 0.5 V，0 VDC 时的输出漏电流为 5.30 mA，以及开/关信号转换的典型响应时间。

该IC670MDL740配有由 25 个端子组成的集成接线端子。每个端子设计用于端接一根 AWG #14 - AWG #22 电线或使用 AWG #2 电线的两 （18） 根电线。在此模块上安装外部跳线后，允许的电线尺寸减小到 AWG #14 至 AWG #16。

现场控制IC670MDL740直流输出模块是GE Fanuc的正逻辑输出模块。GE IC670MDL740正逻辑输出模块提供一组 16 个离散输出通道。输出还充当源型输出。输出点的职责是通过将负载切换到直流电源的正极来向负载提供电流。模块内有一个 5 安培保险丝，用于连接外部电源。输出能够在 10 至 30 伏直流范围内切换负载，同时提供每点 0.5 安培的最大电流。每个输出都连接到状态指示灯 LED，以指示该输出的开/关状态。

IC670MDL740正逻辑输出模块从总线接口单元的电源汲取 111 毫安的最大电流。模块的状态指示灯指示保险丝熔断故障以及用户电源电压是否低于 9.8 伏直流电。如果电源连接不正确，则熔断保险丝。这意味着保险丝有助于保护输出免受外部电源极性误差的影响。它还有助于保护模块免受流过输出点的过大电流的影响。建议用户使用具有 5 Amps 额定电流和 250 伏交流电压的慢熔断型保险丝tage 额定值。该模块还可以将熔断的保险丝诊断消息发送到总线接口单元。IC670MDL740 正逻辑输出模块具有 2 安培的最大浪涌电流、0.5 安培的最大负载电流和 1 毫安的最小负载电流。

IC670MDL740 正逻辑分立输出模块 通用输出模块

【英文介绍】

The IC670MDL740 is a positive logic discrete output module manufactured by GE Fanuc. This module is a universal output module that is installed on the Bus Interface Unit (BIU) to implement an extended I/O solution. It is commonly used in powered output devices, such as indicator lights, relay coils, solenoid drive devices, and similar devices with low current ratings. This is because the IC670MDL740 provides an output current of 10.30 amps per channel and a total output current of 24 amps per module at a voltage output range of 0-5 VDC and a nominal voltage of 4 VDC.

The IC670MDL740 is designed with a separate status LED indicator indicating the on/off status of each output channel of the module. A common fuse is installed throughout the I/O group, which is also assigned an LED indicator to describe the blown fuse status. The module generates a rated surge current of 2 amps with a maximum duration of 100 ms. The minimum load current of the output channel is 1 mA per point, the output voltage drop is 0.5 V, the output leakage current is 5.30 mA at 0 VDC, and the typical response time of the on/off signal conversion.

The IC670MDL740 is equipped with an integrated terminal consisting of 25 terminals. Each terminal is designed to terminate one AWG # 14-AWG #22 wire or two (18) wires using AWG #2 wire. After installing external jumpers on this module, the allowable wire size is reduced to AWG #14 to AWG #16.

Field control IC670MDL740 DC output module is the positive logic output module of GE Fanuc. The GE IC670MDL740 positive logic output module provides a set of 16 discrete output channels. The output also acts as a source-type output. The responsibility of the output point is to provide current to the load by switching the load to the positive terminal of the DC power supply. There is a 5 amp fuse inside the module to connect to an external power supply. The output is capable of switching loads in the range of 10 to 30 volts DC while providing a maximum current of 0.5 amps per point. Each output is connected to a status indicator LED to indicate the on/off status of that output.

The IC670MDL740 positive logic output module draws a maximum current of 111 mA from the power supply of the bus interface unit. The module's status indicator indicates a blown fuse failure and whether the user's supply voltage is below 9.8 volts DC. If the power connection is not correct, blow the fuse. This means that the fuse helps protect the output from polarity errors in the external power supply. It also helps protect the module from excessive current flowing through the output point. Users are advised to use a slow fuse tage rating with a 5 Amps current rating and 250 volts AC voltage. The module can also send a blown fuse diagnostic message to the bus interface unit. The IC670MDL740 positive logic output module has a maximum surge current of 2 amps, a maximum load current of 0.5 amps, and a minimum load current of 1 mA.

IC670MDL740 正逻辑分立输出模块 通用输出模块

【其他型号推荐】