GE IC670MDL640 离散输入模块 总线接口单元 

【产品详情】

IC670MDL640是GE Fanuc制造的Filed control系列的一部分。该模块设计用作扩展输入模块，安装在总线接口单元 （BIU） 模块所在的模块上。它带有十六 （16） 个输入通道，支持正负逻辑接线配置。由于支持此类接线配置，该模块适用于不同的区域，因为正负逻辑接线利用率有时由特定区域或安装区域内的适用标准决定。

IC670MDL640输入通道设计用于接受 0-30 VDC 的输入信号电压范围，标称电压为 24 VDC，用户输入电流为每点 7.5 mA。该模块的电流消耗为 75 mA，由总线接口单元 （BIU） 电源供电，所有输入均处于活动状态，最大电流消耗为 83 mA。

该模块的正逻辑额定导通电压为 +15 VDC 至 +30 VDC，负逻辑额定电压为 -15 VDC 至 -30 VDC，而正逻辑配置的关断状态电压为 0 至 +5VDC，负逻辑配置的关断状态电压为 0 至 -5VDC。此外，导通状态电流为 3.0 mA 至 8 mA，而关断状态电流为 0 至 -5VDC。该模块的输入通道相似，典型响应时间为 6 ms，最大响应时间为 10 ms。该模块的典型输入阻抗为 3K 欧姆。

该模块IC670MDL640是GE Fanuc通过IC670产品线提供的现场控制单元之一。该模块具有 16 个具有正/负逻辑的输入，允许用户根据应用要求使用输入。IC670MDL640分立式输入模块支持特殊的键控功能，并连接到相应的接线端子上。该装置与各种可编程逻辑控制器兼容，适用于目录号为 IC670 和 IC670MDL 的型号。该装置是现场控制系列的一部分，是按照 CE 和 UL 标准等标准中规定的要求制造的。现场控制组件严格为在标准工业环境中使用而制造，但不适用于危险场所。

IC670MDL640模块与电子连接的盒式端子一起使用，设计用于 0 至 30 伏直流的工作电压。本机的额定电压为 24 伏直流电。除此之外，每个点的用户输入电流为 7.5 毫安，电流消耗为 75 毫安（典型值）。连接到总线接口单元的电源的最大电流为 83 毫安。IC670MDL640模块等模块是提供对工业应用过程控制的重要设备，它可以用作独立控制器网络的一部分。该组件不会浪费面板空间，并且由于具有各种安全功能，因此降低了总体成本。

GE IC670MDL640 离散输入模块 总线接口单元 

【英文介绍】

The IC670MDL640 is part of the Filed control family manufactured by GE Fanuc. This module is designed to be used as an expansion input module and is mounted on the module where the Bus Interface Unit (BIU) module is located. It comes with sixteen (16) input channels and supports positive and negative logic wiring configurations. Due to the support for such wiring configurations, the module is suitable for different regions, as positive and negative logic wiring utilization is sometimes determined by applicable standards within a specific region or installation area.

The IC670MDL640 input channel is designed to accept an input signal voltage range of 0-30 VDC, with a nominal voltage of 24 VDC and a user input current of 7.5 mA per point. The module has a current consumption of 75 mA and is powered by a Bus Interface Unit (BIU) power supply with all inputs active and a maximum current consumption of 83 mA.

The module has positive logic rated on-voltage from +15 VDC to +30 VDC, negative logic rated voltage from -15 VDC to -30 VDC, and positive logic configured off state voltage from 0 to +5VDC and negative logic configured off state voltage from 0 to -5VDC. In addition, the on-state current is 3.0 mA to 8 mA, while the off state current is 0 to -5VDC. The input channels of this module are similar, with a typical response time of 6 ms and a maximum response time of 10 ms. The typical input impedance of this module is 3K ohms.

The module IC670MDL640 is one of the field control units offered by GE Fanuc through the IC670 product line. The module has 16 inputs with positive/negative logic, allowing users to use inputs according to application requirements. The IC670MDL640 discrete input module supports special keying functions and is connected to the appropriate terminal. The unit is compatible with a variety of programmable logic controllers and is suitable for models with catalog numbers IC670 and IC670MDL. The unit is part of the field control series and is manufactured in accordance with the requirements specified in standards such as CE and UL standards. Field control components are manufactured strictly for use in standard industrial environments, but not for use in hazardous locations.

The IC670MDL640 module is used with electronically connected box terminals and is designed for operating voltages from 0 to 30 volts DC. The rated voltage of this unit is 24 volts DC. In addition to this, the user input current at each point is 7.5 mA and the current consumption is 75 mA (typical values). The maximum current of the power supply connected to the bus interface unit is 83 MA. Modules such as the IC670MDL640 module are important devices that provide process control for industrial applications and can be used as part of an independent controller network. This component does not waste panel space and reduces the overall cost due to various safety features.

GE IC670MDL640 离散输入模块 总线接口单元 

【其他型号推荐】