IC200SET001 电源模块 具有隔离电源

【产品详情】

GE Fanuc Versamax IC200PWR202 电源模块具有高达 3 伏直流扩展电源的扩展功能。该模块不像 Versamax 系列的其他电源模块那样具有隔离电源。该装置为backpPLC通道设备供电，包括I/O模块、CPU和NIU。它充当系统中的主电源或辅助电源，尤其是当它安装在电源升压器载体上时。GE Fanuc IC200PWR202电源模块的输入电压范围在 9.6 到 15 伏直流之间，标称电压为 12 伏直流。它还具有 5 伏直流或 3.3 伏直流的输出电压。该模块的保持时间约为 10 毫秒，额定输入功率为 11 瓦。

该IC200PWR202是由GE智能平台控制系统解决方案公司生产的具有扩展功能的VersaMax电源模块。 该电源为背板设备（如中央处理器、网络接口单元以及输入和输出模块）供电。当连接到电源升压载波时，IC200PWR202可以充当主电源或补充电源。IC200PWR202高 5.25 英寸（133.4 毫米）。它的尺寸为 1.93 英寸宽（49 毫米）和 1.54 英寸深（39 毫米）。

IC200PWR202的输入电压可以是 9.6 伏到 15 伏的直流电，也称为 VDC;但是，标称输入电压为 12 VDC。输入功率额定为 11 瓦，保持时间为 10 毫秒。输出电压有两种选择：5 伏直流电和 3.3 伏直流电。当使用 3.3 伏直流输出电压时，该设备将提供 1.0 的最大输出电流ampere.当使用 5 伏直流输出电压时，该模块将提供高达 1.5 安培的输出电流。注意：总输出电流不应超过 1.5 amperes.

当在 12 伏直流电下运行时，IC200PWR202的浪涌电流将为 25 安培，当在 15 伏直流电下运行时，浪涌电流将为 30 安培。对于现场布线，DC- 应接地到框架接地和/或接地。由于 DC- 与电源内部的框架接地，因此不能选择浮动电源。为确保本设备的安全运行，采用以下保护措施：短路保护、过载保护、反向电压极性保护。

GE Fanuc IC200PWR202电源模块的浪涌电流额定值为 25 安培（12 伏直流）和 30 安培（15 伏直流）。IC200PWR202电源模块的总输出电流不应超过 1.5 Amps。当输出电压为 3.3 伏直流电时，输出电流将为 1.0 安培。当以 5 伏直流电的输出电流运行时，最大输出电流将为 1.5 安培减去 3.3 伏的已用电压。电源模块设计用于提供反极性、短路和过载保护。IC200PWR202电源模块的尺寸为 49 毫米（1.93 英寸）x 133.4 毫米（5.25 英寸 x 39 毫米（1.54 英寸），不包括 DIN 导轨或托架的高度。

IC200SET001 电源模块 具有隔离电源

【英文介绍】

The GE Fanuc Versamax IC200PWR202 power module features an extended power supply up to 3 volts DC. The module does not have an isolated power supply like other Psus in the Versamax family. The unit powers backpPLC channel devices, including I/O modules, cpus, and NIU. It acts as a primary or secondary power source in the system, especially when it is mounted on a power booster carrier. The GE Fanuc IC200PWR202 power module has an input voltage range between 9.6 and 15 volts DC, with a nominal voltage of 12 volts DC. It also has an output voltage of 5 volts DC or 3.3 volts DC. The module has a hold time of about 10 milliseconds and an input power rating of 11 watts.

The IC200PWR202 is an extendable VersaMax power module manufactured by GE Intelligent Platform Control System Solutions. This power supply powers backplane devices such as the central processing unit, network interface units, and input and output modules. When connected to a power boost carrier, the IC200PWR202 can act as a main or supplementary power supply. The IC200PWR202 is 5.25 inches (133.4 mm) tall. It measures 1.93 inches wide (49 mm) and 1.54 inches deep (39 mm).

The input voltage of the IC200PWR202 can be 9.6 volts to 15 volts of direct current, also known as VDC; However, the nominal input voltage is 12 VDC. The input power is rated at 11 watts and the hold time is 10 milliseconds. There are two options for output voltages: 5 volts DC and 3.3 volts DC. When using 3.3 volts DC output voltage, the device will provide a maximum output current of 1.0 ampere. When using a 5-volt DC output voltage, the module will deliver an output current of up to 1.5 amps. Note: The total output current should not exceed 1.5 amperes.

When operating at 12 volts DC, the IC200PWR202 will have a surge current of 25 amps and when operating at 15 volts DC, the surge current will be 30 amps. For field wiring, DC-should be grounded to the frame and/or grounded. Since the DC- is grounded to the frame inside the power supply, a floating power supply cannot be selected. In order to ensure the safe operation of the equipment, the following protection measures are adopted: short circuit protection, overload protection, reverse voltage polarity protection.

The GE Fanuc IC200PWR202 power supply module has surge current ratings of 25 amps (12 volts DC) and 30 amps (15 volts DC). The total output current of the IC200PWR202 power module should not exceed 1.5 Amps. When the output voltage is 3.3 volts DC, the output current will be 1.0 amps. When operating at an output current of 5 volts DC, the maximum output current will be 1.5 amps minus 3.3 volts of used voltage. Power modules are designed to provide reverse polarity, short circuit, and overload protection. The IC200PWR202 power module measures 49 mm (1.93 in) x 133.4 mm (5.25 in x 39 mm (1.54 in), not including the height of the DIN rail or bracket.

IC200SET001 电源模块 具有隔离电源

【其他型号推荐】