IC200PNS002  双工连接端口  中央处理器

【产品详情】

GE Fanuc Versamax IC200PNS002 PROFINET 扫描仪 （PNS） 模块需要 7.0 或更高版本的 Proficy Machine Edition 软件和固件版本 3.7 或更高版本的 RX0i PLC 中央处理器。该模块有 2 个额定速率为 100 Mbps 的 SC 双工连接端口。Versamax PROFINET 扫描器 LED 包括电源 LED，即“PWR1”和“PWR2”LED，亮起时呈绿色常亮。当模块正常运行时，“OK”LED 变为稳定的绿色。当通电故障或机器错误时，其他模块的“OK”LED 通常熄灭或闪烁，如果扫描仪未设置为自动重启，“OK”LED 将闪烁琥珀色。“FAULT”LED 显示 Versamax 节点的状态。如果 PROFINET 扫描器模块或节点中的模块上没有 PROFINET 诊断，则 LED 通常熄灭。如果存在诊断条件，“FAULT”LED 会呈琥珀色常亮。

IC200PNS002是GE的VersaMax PROFINET扫描器，可将VersaMax模块的远程节点连接到PROFINET I/O控制器。 IC200PNS002可以扫描模块，恢复输入数据，并提供输出数据。它还可以在PROFINET网络上以构建的生产速率打印输入数据。IC200PNS002管理远程节点和控制器内模块之间的 PROFINET 通信和模块配置。此外，如果网络通信丢失，扫描程序会管理呈现到不同模块配置的 I/O 状态。

该IC200PNS002在 1VDC 电源下消耗 10.5A，并支持冗余电源。冗余电源可以安装在IC200PNS002上，而不会干扰系统运行。安装冗余电源时，必须关闭电源的电源。将冗余电源模块安装到空电源位置后，可以打开冗余电源的电源并分析 PWR LED 以确认适当的电源。

使用IC200PNS002时，不应尝试混合使用隔离电源和非隔离电源。如果使用隔离式电源，则该区域中的所有电源都应为隔离式电源。在 PNS 或升压器上混合使用非隔离式交流电源与非隔离式直流电源没有任何限制。该IC200PNS002配备了 10 个 LED，用于指定电源并显示操作模式和状态。

GE Fanuc Versamax IC200PNS002 PROFINET 扫描仪 （PNS） 模块还有一个“CONNECT”LED，当设备通电时会闪烁琥珀色，表示它尚未准备好使用。稍后，它变为绿色常亮，表示设备已与主 I/O 控制器建立通信。当 IC200PNS002 扫描仪模块更新固件时，“CONNECT”LED 呈琥珀色快速闪烁，表示所有连接均已阻止。“LAN”LED 闪烁表示扫描器正在加载以太网数据包，并在没有活动时关闭。IC200PNS002 扫描仪模块的正常工作温度范围为 0 至 60 摄氏度，尺寸为高 132 毫米（5.2 英寸）和宽 134 毫米（5.28 英寸）。

IC200PNS002  双工连接端口  中央处理器

【英文介绍】

The GE Fanuc Versamax IC200PNS002 PROFINET Scanner (PNS) module requires Proficy Machine Edition software version 7.0 or higher and RX0i PLC firmware version 3.7 or higher The central processing unit. The module has two SC duplex connection ports rated at 100 Mbps. The Versamax PROFINET scanner leds include power leds, namely "PWR1" and "PWR2" leds, which are green when lit up. When the module is operating normally, the "OK" LED turns steady green. When there is a power failure or machine error, the "OK" LED of the other modules usually goes out or flashes, and if the scanner is not set to restart automatically, the "OK" LED will flash amber. The FAULT LED displays the status of the Versamax node. If there is no PROFINET diagnostics on the PROFINET scanner module or module in the node, the LED is usually off. If a diagnostic condition is present, the "FAULT" LED will be amber steady on.

The IC200PNS002 is GE's VersaMax PROFINET scanner that connects remote nodes of the VersaMax module to the PROFINET I/O controller. The IC200PNS002 can scan modules, recover input data, and provide output data. It can also print input data at the built production rate on the PROFINET network. IC200PNS002 manages PROFINET communication and module configuration between remote nodes and modules within the controller. In addition, if network communication is lost, the scanner manages the I/O state presented to different module configurations.

The IC200PNS002 consumes 10.5A at 1VDC power and supports redundant power. Redundant power supplies can be installed on the IC200PNS002 without interfering with system operation. When installing redundant Psus, power off the Psus. After installing the redundant power supply module to the empty power supply location, you can turn on the power to the redundant power supply and analyze the PWR LED to confirm the appropriate power supply.

When using the IC200PNS002, you should not attempt to mix isolated and non-isolated power supplies. If isolated power supplies are used, all power supplies in this area should be isolated power supplies. There are no restrictions on mixing a non-isolated AC power supply with a non-isolated DC power supply on a PNS or booster. The IC200PNS002 is equipped with 10 leds to specify the power supply and display the operating mode and status.

The GE Fanuc Versamax IC200PNS002 PROFINET Scanner (PNS) module also has a "CONNECT" LED that flashes amber when the device is powered on, indicating that it is not yet ready for use. Later, it turns green, indicating that the device has established communication with the primary I/O controller. When the IC200PNS002 scanner module updates its firmware, the "CONNECT" LED flashes a rapid amber, indicating that all connections have been blocked. The "LAN" LED flashing indicates that the scanner is loading Ethernet packets and turning off when there is no activity. The IC200PNS002 scanner module has a normal operating temperature range of 0 to 60 degrees Celsius and a size of 132 mm (5.2 in) high and 134 mm (5.28 in) wide.

IC200PNS002  双工连接端口  中央处理器

【其他型号推荐】