GE IC200PNS001  网络接口单元 用作嵌入式交换机

【产品详情】

IC200PNS001是 VersaMax 产品系列中的 Profinet 网络接口单元。它主要用于利用Profinet工业协议实现分布式I/O架构，特别是Profinet从站版本2.2 A 类I/O设备。该模块不仅可以与 VersaMax 系列一起使用，还可以与其他控制器一起使用，例如 PACSystem、RX3i 和 RX7i 控制器。

该IC200PNS001安装有两 （2） 个 RJ45 端口，用作嵌入式交换机，仅使用单个 IP 地址。可用于不同的以太网拓扑结构，特别是线性、星形和环形。两个端口都支持 10/100 mbps 的传输速率，能够处理总共 2880 字节的离散输入和输出，特别是 1440 字节的输入数据和 1440 字节的输出数据。同样，该模块可以处理多达 2880 字节的模拟 I/O，特别是 1440 字节的模拟输入和 1440 字节的模拟输出。对于诊断数据，该模块内置 32 个输入状态位和 32 个输出控制位。

每个IC8PNS200实例最多可安装八 （001） 个 VersaMax I/O 模块和托架。它具有 1ms、2ms、4ms、8ms、16ms、32ms、64ms、128ms、256ms 和 512ms 的可配置数据更新速率。该模块具有 5 VDC 背板电流消耗，功耗为 3 瓦，物理尺寸为 134 毫米（5.28 英寸）x 132 毫米（5.2 英寸）。

IC200PNS001使用10/100BASE-T传输介质，每段最大电缆距离为100米，可以使用以太网交换机或光纤介质转换器等介质转换器进行扩展。

GE Fanuc Versamax IC200PNS001 PROFINET 扫描仪 （PNS） 模块需要固件版本为 3.7 或更高版本的 RX0i PLC CPU，以及 Proficy Machine Edition 软件版本 7.0 或更高版本。该模块将 Versamax 远程节点与 PROFINET I/O 网络进行协调。GE Fanuc IC200PNS001 PROFINET扫描器（PNS）模块具有输入数据检索和输出数据传输等功能。它具有 PROFINET 警报和诊断报告等功能，允许对已断电的过度电源进行热插拔，并允许使用具有超网和子网的无类别域间路由进行配置。它还提供现场升级选项，固件可以通过 USB 端口更新（该端口仅用于固件升级，不用于永久连接）。

GE Fanuc IC200PNS001 PROFINET Scanner （PNS） 模块可以将远程节点连接到 PROFINET I/O 网络，以便在通信丢失时监督 I/O 状态。其他功能包括模块扫描（输出和输入扫描）、管理模块配置、PROFINET 扫描器节点内模块和 I/O 控制器之间的 PROFINET 通信，以及以诊断和警报的形式向 I/O 控制器报告或发出故障信息。此外，PNS 模块的主远程 I/O 将 PROFINET 网络上的数据发布到 I/O 控制器，并接收 PROFINET 网络上 I/O 控制器生成的数据。该模块的工作温度范围在 0 到 60 摄氏度之间，适用于周围空气温度，没有风扇。

GE IC200PNS001  网络接口单元 用作嵌入式交换机

【英文介绍】

The IC200PNS001 is a Profinet network interface unit in the VersaMax product family. It is mainly used to implement distributed I/O architectures using the Profinet industrial protocol, especially Profinet slave version 2.2 Class A I/O devices. The module can be used not only with the VersaMax family, but also with other controllers, such as PACSystem, RX3i and RX7i controllers.

The IC200PNS001 has two (2) RJ45 ports installed and is used as an embedded switch, using only a single IP address. It can be used in different Ethernet topologies, especially linear, star, and ring. Both ports support 10/100 mbps transfer rates and are capable of handling a total of 2880 bytes of discrete input and output, specifically 1440 bytes of input data and 1440 bytes of output data. Similarly, the module can handle up to 2880 bytes of analog I/O, specifically 1440 bytes of analog input and 1440 bytes of analog output. For diagnostic data, 32 input status bits and 32 output control bits are built into the module.

Each IC8PNS200 instance can install up to eight (001) VersaMax I/O modules and brackets. It has configurable data update rates of 1ms, 2ms, 4ms, 8ms, 16ms, 32ms, 64ms, 128ms, 256ms and 512ms. The module has a 5-VDC backplane current consumption, a power consumption of 3 watts, and a physical size of 134 mm (5.28 in) x 132 mm (5.2 in).

The IC200PNS001 uses 10/100BASE-T transmission media with a maximum cable distance of 100 meters per segment and can be extended with media converters such as Ethernet switches or fiber optic media converters.

The GE Fanuc Versamax IC200PNS001 PROFINET Scanner (PNS) module requires an RX0i PLC CPU with firmware version 3.7 or higher. And Proficy Machine Edition software version 7.0 or higher. The module coordinates Versamax remote nodes with the PROFINET I/O network. The GE Fanuc IC200PNS001 PROFINET Scanner (PNS) module has functions such as input data retrieval and output data transmission. It features features such as PROFINET alerts and diagnostic reports, allows hot swapping of overpowered power supplies that have been disconnected, and allows configuration using classless interdomain routing with hypernets and subnets. It also offers an on-site upgrade option, and the firmware can be updated via a USB port (this port is only used for firmware upgrades, not permanent connections).

The GE Fanuc IC200PNS001 PROFINET Scanner (PNS) module connects remote nodes to the PROFINET I/O network to monitor I/O status in the event of communication loss. Additional functions include module scanning (output and input scanning), management module configuration, PROFINET communication between modules and I/O controllers within the PROFINET scanner node, and reporting or issuing fault information to the I/O controller in the form of diagnostics and alerts. In addition, the primary remote I/O of the PNS module publishes data on the PROFINET network to the I/O controller and receives data generated by the I/O controller on the PROFINET network. The module operates in a temperature range between 0 and 60 degrees Celsius, suitable for ambient air temperatures, without a fan.

GE IC200PNS001  网络接口单元 用作嵌入式交换机

【其他型号推荐】