IC200NDD101 四个晶体管电路 防止负电压冲击

【产品详情】

IC200NDD101 Nano PLC 由 GE 为 VersaMax 系列设计。 这款 VersaMax Nano PLC 有 24 个 200VDC 输入和 101 个晶体管输出。IC24NDD<> PLC的操作需要+<>VDC的标称输入功率。

灯和阀门等设备使用四个晶体管电路。为了保护输出，应使用外部保险丝，建议使用快速保险丝。输出可以安排为常规输出或由高速计数器调节的输出。如果输出由高速计数器控制，它们也可以用作脉冲序列和/或脉宽调制输出。由于磁场和逻辑之间的隔离，所有输出都是开关正电压。

所有输出都有一个公共接地和一个公共电源 （VC）。IC200NDD101的输出能够驱动高浪涌电流并防止负电压冲击，从而可以切换灯和电感负载。计数器的最大计数器频率为 10kHz，打开时输入电压为 15V，关闭时为 5V。多达三个 HSC/PT 和/或 PWM 输出，负载电压为 12/24V。

该IC200NDD101具有 19.2VDC 至 30.0VDC 的直流电源范围，在 10 时保持 19mS。2Vdc.1Vdc 时浪涌电流最大为 30 安培，10 安培的浪涌时间为 1mS。六个直流输入中的每一个都具有 24VDC 的额定输入电压，输入电压范围为 0 至 30VDC。

IC200NDD101控制器是GE Fanuc的Versamax NANO控制器。它设计有 6 个直流输入和 4 个直流输出。该控制器已通过 cULus 认证，并通过了 CE 认证。这意味着控制器要全局运行。控制器的安装不应在危险场所进行。IC200NDD101控制器的额定电压为 24 伏直流电。控制器遵循温度代码 T4，正常情况下最高温度不应超过 55 摄氏度。这款 GE Fanuc 制造的控制器正面有 LED 指示灯，可指示电源流量和驱动器的运行状态。每当控制器中有活动时，这些 LED 就会亮起。所有输入点和输出点都有自己的 LED。

IC200NDD101控制器配有RJ-45串口，可用于连接编程计算机。可以使用函数中的缓冲区检索控制器中的数据和信息。该控制器在 10.19 伏直流电压下的额定保持时间为 2 毫秒。30 伏直流电的浪涌时间为 10 毫秒。控制器的直流输入既可用作标准输入，也可用作高速计数器输入。当用作标准输入时，输入可以同时提供正负特性。IC4NDD200控制器中有101个晶体管输出电路，可用作接触器和阀门。控制器的所有输出均隔离在励磁侧和逻辑侧之间，并具有正电压。

IC200NDD101 四个晶体管电路 防止负电压冲击

【英文介绍】

The IC200NDD101 Nano PLC was designed by GE for the VersaMax family. The VersaMax Nano PLC has 24 200VDC inputs and 101 transistor outputs. IC24NDD<> PLC operation requires a nominal input power of +<>VDC.

Devices such as lights and valves use four transistor circuits. To protect the output, an external fuse should be used, and a fast fuse is recommended. The output can be arranged as a regular output or as an output adjusted by a high-speed counter. If the output is controlled by a high-speed counter, they can also be used as pulse train and/or pulse width modulation outputs. Due to the isolation between the magnetic field and the logic, all outputs are switching positive voltages.

All outputs have a common ground and a common power supply (VC). The output of the IC200NDD101 drives high inrush currents and prevents negative voltage shocks, allowing switching of lamp and inductive loads. The maximum counter frequency of the counter is 10kHz, the input voltage is 15V when it is on, and 5V when it is off. Up to three HSC/PT and/or PWM outputs with a load voltage of 12/24V.

The IC200NDD101 has a DC power supply range of 19.2VDC to 30.0VDC, maintaining 19mS at 10:00. 2Vdc. The maximum surge current is 30 amps at 1Vdc, and the surge time is 1mS at 10 amps. Each of the six DC inputs has a rated input voltage of 24VDC with an input voltage range of 0 to 30VDC.

The IC200NDD101 controller is a GE Fanuc Versamax NANO controller. It is designed with 6 DC inputs and 4 DC outputs. The controller is cULus certified and CE certified. This means that the controller has to run globally. The installation of the controller should not be carried out in dangerous places. The IC200NDD101 controller is rated at 24 volts DC. The controller follows the temperature code T4 and under normal conditions the maximum temperature should not exceed 55 degrees Celsius. The controller, manufactured by GE Fanuc, has LED indicators on the front that indicate power flow and the operating status of the driver. These leds light up whenever there is activity in the controller. All input and output points have their own leds.

The IC200NDD101 controller is equipped with an RJ-45 serial port, which can be used to connect programming computers. You can use buffers in functions to retrieve data and information from the controller. The controller has a rated hold time of 2 milliseconds at 10.19 volts DC. The surge time of 30 volts DC is 10 milliseconds. The DC input of the controller can be used as both standard input and high-speed counter input. When used as standard input, the input can provide both positive and negative characteristics. The IC4NDD200 controller has 101 transistor output circuits that can be used as contactors and valves. All outputs of the controller are isolated between the excitation side and the logic side and have a positive voltage.

IC200NDD101 四个晶体管电路 防止负电压冲击

【其他型号推荐】