IC200MDL930 继电器输出通道 干触点输出

【产品详情】

该IC200MDL930是一个八 （8） 通道输出模块，属于 VersaMax I/O 平台，以前由 GE 智能平台 （GE IP） 提供，目前隶属于艾默生自动化。该模块在常开 （N.O.） 或 A 型触点位置带有单独隔离的继电器输出通道。该模块的内置继电器为固定线圈、移动电枢型，继电器触点由银合金制成。这些触点输出适用于为在不同电压类别下运行的电气负载供电，特别是在 0 至 125Hz 交流电压频率下，0 至 265VDC 和 47 至 63VAC。

IC200MDL930触点输出本质上是干触点输出。它需要一个外部电源电压源来将适当的电压传导到连接的电气负载。它可以与电阻或导电负载一起使用，但是，对于导电负载，建议安装外部保护或抑制电路，例如保险丝。输出触点的额定电流最小为每点 10mA;2.0A 用于 5 至 265VAC，最大值;最大 2 至 0 VDC 为 5.30A，最大 0.2A 为 31 至 125 VDC。所有额定电流均针对阻性负载进行额定。此外，触点输出的标称外部电源电压额定值为 5/24/125VDC 和 120/240VAC。

当所有输出通电时，IC200MDL930的最大背板电流消耗为245 mA。该模块配有单独的通道指示器，用于描述每个输出通道的通电状态。它还具有单个模块 OK LED，用于指示模块接收的背板电源的有源电源。

IC200MDL930模块是GE Fanuc制造的8点输出模块。它是 Versamax 系列的一部分。模块的输出点是单独隔离的。输出模块从背板汲取 245 毫安的功率，所有输出均已激活。IC200MDL930模块与交流和直流负载完全兼容。模块的 8 个点有自己的 LED 指示灯，用于指示通过这些点的场电源的存在。默认情况下，模块接触点在模块的活动期间关闭。此时输出位设置为 1。在背板上使用机架安装方法时，模块的安装很容易。输出模块已通过 CE、cULus 和其他工业标准认证。它是为在全局设置中使用而设计的。

IC200MDL930输出模块是一种智能设备，可以比其他同类模块执行更快的处理。该输出模块没有输出漏电流。每个点的继电器都设计有固定线圈和电枢。开/关的响应时间比其他 Versamax 模块慢，时间为 10 毫秒。该模块的开关频率为每分钟 20 个周期，适用于感性负载。此输出模块型号中没有内部保险丝或缓冲器。IC200MDL930模块采用强制风冷冷却，使其环境温度保持在 0 到 30 摄氏度之间。当环境温度超过最高额定温度时，热降额开始。

IC200MDL930 继电器输出通道 干触点输出

【英文介绍】

The IC200MDL930 is an eight (8) channel output module from the VersaMax I/O platform, previously supplied by GE Intelligent Platforms (GE IP) and currently owned by Emerson Automation. The module has A separate relay output channel at the normally open (N.O.) or type A contact position. The built-in relay of the module is a fixed coil, mobile armature type, and the relay contacts are made of silver alloy. These contact outputs are suitable for powering electrical loads operating in different voltage classes, especially at AC voltage frequencies 0 to 125Hz, 0 to 265VDC and 47 to 63VAC.

The IC200MDL930 contact output is essentially a dry contact output. It requires an external supply voltage source to conduct the appropriate voltage to the connected electrical load. It can be used with resistive or conductive loads, however, for conductive loads it is recommended to install an external protection or suppression circuit, such as a fuse. The rated current of the output contact is at least 10mA per point; 2.0A for 5 to 265VAC, Max. The maximum 2 to 0 VDC is 5.30A, and the maximum 0.2A is 31 to 125 VDC. All current ratings are rated for resistive loads. In addition, the nominal external supply voltage ratings for the contact output are 5/24/125VDC and 120/240VAC.

The maximum backplane current consumption of the IC200MDL930 is 245 mA when all outputs are energized. The module is equipped with a separate channel indicator to describe the power-on status of each output channel. It also features a single module OK LED, which is used to indicate the active power supply of the backplane power received by the module.

The IC200MDL930 module is an 8-point output module manufactured by GE Fanuc. It is part of the Versamax series. The output points of the module are isolated. The output module draws 245 mah of power from the backplane, and all outputs are activated. The IC200MDL930 module is fully compatible with AC and DC loads. The 8 points of the module have their own LED indicators that indicate the presence of a field power source passing through these points. By default, module touchpoints are closed during module activity. The output bit is set to 1. Module installation is easy when using the rack mounting method on the backplane. The output modules are CE, cULus and other industry standard certified. It is designed for use in global Settings.

The IC200MDL930 output module is an intelligent device that can perform faster processing than other modules of its kind. The output module has no output leakage current. The relay at each point is designed with a fixed coil and armature. The on/off response time is slower than other Versamax modules at 10 milliseconds. The module has a switching frequency of 20 cycles per minute and is suitable for inductive loads. There is no internal fuse or buffer in this output module model. The IC200MDL930 module uses forced air cooling to keep its ambient temperature between 0 and 30 degrees Celsius. When the ambient temperature exceeds the maximum rated temperature, the heat derating begins.

IC200MDL930 继电器输出通道 干触点输出

【其他型号推荐】