IC200MDL740 正逻辑输出模块 分立式输出模块

【产品详情】

IC200MDL740 分立式输出模块是 GE Fanuc 12/24 伏直流 Versamax 正逻辑输出模块，具有 1 组 16 个源极型输出。它具有机架安装选项，以及带有热插入设施的紧凑设计，可帮助用户轻松更换它，而无需更改现场布线。IC200MDL740 离散输出模块具有 LED，用于指示每个输出点的状态。有 3 种类型的载体可用于在不中断操作的情况下轻松安装或更换系统中的输出模块。它具有可配置的滤波时间、0.2 毫秒的最大导通响应时间和 1.0 毫秒的最大关断响应时间。它还为负载侧提供外部电源，并使用背板电源工作。

该IC200MDL740是通用电气智能平台控制系统解决方案公司制造的 VersaMax 系列的输出模块。 该模块总共有一组 16 个输出点，每个输出点都支持离散数字信号。该器件的输出点可以是正逻辑类型，也可以是源极类型。每个输出点执行负载切换并为负载供电。本产品与IC200CHS系列插入继电器底座兼容。

该器件需要辅助电源来支持输出负载切换。五伏输出电源消耗的电流量不能超过 45 毫安。该模块的工作电压为 10.2 至 30 伏直流电 （DC）。虽然该设备的标称电压为 24 伏直流电，但它也可以在 12 伏直流电下工作;但是，在 12 伏直流电下运行将需要升级到 IC200MDL740B 或更高版本。

每个输出点的电流为 0.5 安培，“开启”状态的响应时间为 0.2 毫秒，“关闭”状态的响应时间为 1.0 毫秒。不支持通道间隔离，也不支持任何保护机制，如内部保险丝。输出电压降峰值为 0.3 V，当工作在 30 V DC 时，输出泄漏高达 0.5 毫安。LED 灯指示设备状态。这些 LED 灯需要现场电源才能运行，但不受输出负载条件的影响。该IC200MDL740还支持在 24 或 30 伏直流电下运行时的热降额。

IC200MDL740 DC 正极逻辑输出模块具有一组带有 DC+ 和 DC- 端子的输出。外部抑制电路必须与输出端的感性负载一起使用。该外部抑制电路可以连接到实际负载上，也可以连接到驱动感性负载的每个输出点。建议在 B 端子上使用具有 2 安培载流能力的短路棒，以添加额外的总线端子。广泛的托架允许用户在不使用任何工具的情况下安装合适的托架。这些简单的连接设施减少了使用此输出模块所需的培训时间和生命周期成本。它还带有配置软件，可轻松执行硬件和网络配置。IC200MDL740 分立式输出模块是一款通用分布式产品，专为工业和商业自动化以及工业控制应用而设计。

IC200MDL740 正逻辑输出模块 分立式输出模块

【英文介绍】

The IC200MDL740 split output module is a GE Fanuc 12/24 VDC Versamax positive logic output module with 1 set of 16 source type outputs. It has a rack-mount option, and a compact design with hot-plug facilities that help users easily replace it without making changes to the field wiring. The IC200MDL740 discrete output module has an LED to indicate the status of each output point. There are 3 types of carriers that can be used to easily install or replace output modules in the system without interrupting operation. It has a configurable filtering time, a maximum on-off response time of 0.2 ms and a maximum turn-off response time of 1.0 ms. It also provides external power to the load side and works with a backplane power supply.

The IC200MDL740 is the output module of the VersaMax family manufactured by GE Intelligent Platform Control System Solutions. The module has a total set of 16 output points, each of which supports discrete digital signals. The output point of the device can be a positive logic type or a source type. Each output point performs load switching and powers the load. This product is compatible with the IC200CHS series plug-in relay base.

The device requires an auxiliary power supply to support output load switching. The current consumption of the five-volt output power supply cannot exceed 45 MA. The module operates at 10.2 to 30 volts direct current (DC). Although the device has a nominal voltage of 24 volts DC, it can also operate on 12 volts DC; However, operating on 12 volts DC will require an upgrade to IC200MDL740B or later.

The current at each output point is 0.5 amps, and the response time is 0.2 ms for the "on" state and 1.0 ms for the "off" state. Isolation between channels is not supported, nor is any protection mechanism such as internal fuses supported. The output voltage drop peaks at 0.3V, with output leakage up to 0.5mA when operating at 30V DC. LED lights indicate device status. These LED lights require field power to operate, but are not affected by output load conditions. The IC200MDL740 also supports heat derating when operating at 24 or 30 volts DC.

The IC200MDL740 DC positive logic output module has a set of outputs with DC+ and DC-terminals. The external suppression circuit must be used with the inductive load at the output. The external suppression circuit can be connected to the actual load or to each output point that drives the inductive load. It is recommended to use a short circuit rod with a 2 amp current carrying capacity on the B terminal to add additional bus terminals. The wide range of brackets allows users to install the right brackets without using any tools. These simple connectivity facilities reduce the training time and lifecycle costs required to use this output module. It also comes with configuration software to easily perform hardware and network configuration. The IC200MDL740 discrete output module is a general-purpose distributed product designed for industrial and commercial automation and industrial control applications.

IC200MDL740 正逻辑输出模块 分立式输出模块

【其他型号推荐】