IC200MDL730 正逻辑输入模块 具有过流保护和短路保护功能

【产品详情】

IC200MDL730 分立输出模块是 GE Fanuc 制造的 24 伏直流 Versamax 正逻辑输入模块。它提供 8 个分立式输出，具有过流保护和短路保护功能。IC200MDL730 分立输出模块具有源型输出，可向负载提供电流。该设备的主要职责是将负载切换到外部直流电源的正极。建议在施加现场电源之前为背板供电 1 秒钟。输出模块上的 LED 指示灯使用琥珀色来指示短路或过载情况等故障的故障检测。这些故障也称为点故障，由 Versamax PLC 系统中的 CPU 检测到。

该IC200MDL730由GE自动化控制公司制造，是一款VersaMax系列分立式输出模块。 该器件提供一组 <> 个输出点，可以是正逻辑或源极类型。该模块上的输出点负责将负载切换到电源的正极，从而为所有负载提供电流。

除了标准背板电源外，该模块还需要外部直流电源来实现输出负载切换。背板电源必须稳定至少一秒钟，然后此设备才能接受现场电源。如果在背板稳定之前施加现场电源，则可能会发生错误的输出点故障。如果检测到短路，需要外部电源为本产品提供足够的现场电源。有关进一步的外部电源要求，请参阅产品文档。

该IC200MDL730提供故障检测诊断，并可确定是否发生了过载或短路。该模块上的每个输出点都具有以下保护机制：电子短路保护 （ESCP） 和过流保护;但是，不支持通道间隔离。

在 2 伏直流电下工作时，每个输出点能够处理高达 30 安培的电流，整个模块能够驱动最大 8 安培的电流。5 伏背板消耗的电流量为 50 毫安。该模块的输出电压为 17.5 至 30 伏直流电。标称输出电压为 24 伏直流电，可接受 0.5 伏的最大输出电压降。

IC200MDL730 分立式输出模块具有 17.5 至 30 伏直流电压和 2.0 安培负载电流，每点 30 伏直流电压。外部电源具有 18 至 30 伏的直流电压额定值，可以在短路情况下为负载供电以及为模块提供现场电源。如果外接电源的功率特性不足，建议使用电池或电容等局部储能装置。安装时，务必准确进行热插，以免损坏背板。用户必须参考安装指南才能将模块正确安装在托架上。IC200MDL730 分立式输出模块没有热降额、组间隔离或点对点隔离。它具有可扩展的架构、紧凑的设计和增强工业控制应用的功能。

IC200MDL730 正逻辑输入模块 具有过流保护和短路保护功能

【英文介绍】

The IC200MDL730 discrete output module is a 24-volt DC Versamax positive logic input module manufactured by GE Fanuc. It offers 8 separate outputs with overcurrent protection and short circuit protection. The IC200MDL730 discrete output module has a source type output that provides current to the load. The primary responsibility of the device is to switch the load to the positive terminal of the external DC power supply. It is recommended to power the backplane for 1 second before applying field power. The LED indicator on the output module uses amber to indicate fault detection for faults such as short circuit or overload conditions. These failures, also known as point failures, are detected by the CPU in the Versamax PLC system.

The IC200MDL730, manufactured by GE Automation and Control, is a VersaMax series discrete output module. The device provides a set of <> output points, which can be of either positive logic or source type. The output point on this module is responsible for switching the load to the positive terminal of the power supply, thus providing current to all the loads.

In addition to the standard backplane power supply, the module also requires an external DC power supply for output load switching. The backplane power supply must be stable for at least one second before this device can accept field power. If field power is applied before the backplane is stabilized, a false output point failure may occur. If a short circuit is detected, an external power supply is required to provide sufficient on-site power for this product. Refer to the product documentation for further external power requirements.

The IC200MDL730 provides fault detection diagnosis and can determine if an overload or short circuit has occurred. Each output point on the module has the following protection mechanisms: Electronic short circuit protection (ESCP) and overcurrent protection; However, inter-channel isolation is not supported.

When operating at 2 volts DC, each output point is capable of handling up to 30 amps, and the entire module is capable of driving up to 8 amps of current. The 5-volt backplane consumes 50 mah of current. The module has an output voltage of 17.5 to 30 volts DC. The nominal output voltage is 24 volts DC and can accept a maximum output voltage drop of 0.5 volts.

The IC200MDL730 discrete output module has 17.5 to 30 volts DC and 2.0 amps of load current at 30 volts DC per point. The external power supply has a DC voltage rating of 18 to 30 volts and can power the load in case of a short circuit as well as provide on-site power to the module. If the power characteristics of the external power supply are insufficient, it is recommended to use a local energy storage device such as a battery or capacitor. To avoid damage to the backplane, perform accurate hot insertion. The user must refer to the installation guide to install the module correctly on the bracket. The IC200MDL730 discrete output module has no thermal derating, inter-group isolation, or point-to-point isolation. It features a scalable architecture, compact design and enhanced functionality for industrial control applications.

IC200MDL730 正逻辑输入模块 具有过流保护和短路保护功能

【其他型号推荐】