IC200MDL243 输入模块 交流现场设备

【产品详情】

GE Fanuc IC200MDL243 Versamax 16 通道离散输入模块是一种输入模块，它接受来自交流现场设备（输入）的交流信号，并在单个公共端返回它们。IC200MDL243 输入模块设计为仅接收来自输入设备的离散输入，这些输入设备可以具有 2 种状态，即开或关/开或闭，这些信号由 CPU 或网络接口模块 （NIU） 智能处理为 Versamax CPU 中的 16 位离散输入数据。IC200MDL243输入模块采用模块化设计，支持热模块插入，从而延长正常运行时间并减少工程和布线时间。IC200MDL243输入模块使用咬接式载板底座安装在 PLC 的背板中，有助于消除复杂的现场布线，并支持模块的热插拔。

IC200MDL243 是一款具有 120 个点的 VersaMax 16 VAC 离散输入模块。 该特定模块提供 16 个隔离输入，这些输入为正逻辑或源极类型。这些输入接收来自交流输入器件的电流，而返回电流则在公共端。每个输入都有一个单独的返回值。为了给IC200MDL243供电，操作从背板开始。CPU或NIU是输入模块智能处理的供应商。LED 是标准配置，可显示每个输入点的背板电源和开/关状态。

用户输入与逻辑和框架接地的隔离为 250 VAC 连续或 1500 VAC，持续 120 分钟，输入电压标称值为 0 VAC 或 132 至 70 VAC。导通和关断状态电压分别为 132 至 0 VAC 和 20 至 5 VAC，导通和关断状态电流最小值为 2mA，最大值为 5.8mA。该模块的输入阻抗分别为 6.60k 欧姆（10HZ）和 32.50k 欧姆（<>Hz）。

安装IC200MDL243时，用户应首先检查所有组件在运输过程中是否发生任何损坏。如果组件的任何部分损坏，则应更换，因为损坏可能会影响设备的整体性能。安装人员应注意，如果垂直（A、B）安装在 DIN 导轨上，则 16 点模块不需要降额。如果水平安装，其他形式的安装将需要在 132 VAC 下降额。如果热插入不正确，背板上的其他模块可能会受到负面影响，因此应严格遵循正确的程序。

IC200MDL243输入模块具有 16 个单独隔离的输入通道，能够提供正逻辑或源极输入。每个输入点与下一个输入点之间有 250 伏交流连续隔离，模块和接地之间也有 250 伏交流连续隔离。IC200MDL243输入模块不支持外部电源，因为它从背板汲取所有电源。IC200MDL243 输入模块在 100.5 V 电压下具有 0 毫安的最大背板电流，每点的最小可能负载为 5.0 毫安。IC200MDL243 输入模块的标称电压额定值为 120 伏交流电，可接受的输入范围为 0 至 132 伏交流电。IC200MDL243 输入模块具有 70 至 132 伏交流导通状态工作范围，最大响应时间为 1 个周期。IC200MDL243 输入模块有 16 个 LED，用于指示每个输入点的状态，以及一个显示背板工作状态的状态 LED。

IC200MDL243 输入模块 交流现场设备

【英文介绍】

The GE Fanuc IC200MDL243 Versamax 16-channel discrete input module is an input module that accepts AC signals from AC field devices (inputs) and returns them at a single common end. The IC200MDL243 input module is designed to receive only discrete inputs from input devices that can have 2 states, on or off/on or off, and these signals are intelligently processed by the CPU or Network Interface Module (NIU) into 16-bit discrete input data in the Versamax CPU. The IC200MDL243 input module has a modular design and supports hot module insertion, which increases uptime and reduces engineering and wiring time. The IC200MDL243 input module is mounted in the backplane of the PLC using a bite carrier base, which helps eliminate complex field wiring and supports hot-swapable modules.

The IC200MDL243 is a VersaMax 16 VAC discrete input module with 120 points. This particular module provides 16 isolated inputs, which are of either positive logic or source type. These inputs receive the current from the AC input device, while the return current is at the common end. Each input has a separate return value. To power the IC200MDL243, the operation starts from the backplane. CPU or NIU are the suppliers of intelligent processing for input modules. Leds are standard and show the backplane power and on/off status at each input point.

The isolation of the user input from the logic and frame ground is 250 VAC continuous or 1500 VAC for 120 minutes, and the input voltage is nominal 0 VAC or 132 to 70 VAC. On and Off state voltages are 132 to 0 VAC and 20 to 5 VAC respectively, with a minimum on and off state current of 2mA and a maximum current of 5.8mA. The input impedances of the module are 6.60k ohms (10HZ) and 32.50k ohms (<>Hz).

When installing IC200MDL243, the user should first check all components for any damage during transportation. If any part of the component is damaged, it should be replaced, as damage may affect the overall performance of the device. Installers should note that 16-point modules do not require derating if mounted vertically (A, B) on DIN rails. If installed horizontally, other forms of installation will require a drop in the amount of 132 VAC. If hot insertion is not correct, other modules on the backplane may be negatively affected, so correct procedures should be strictly followed.

The IC200MDL243 input module has 16 individually isolated input channels capable of providing positive logic or source input. There is 250 volts AC continuous isolation between each input point and the next input point, and 250 volts AC continuous isolation between the module and the ground. The IC200MDL243 input module does not support external power because it draws all power from the backplane. The IC200MDL243 input module has a maximum backplane current of 0 mA at 100.5 V voltage and a minimum possible load of 5.0 mA per point. The IC200MDL243 input module has a nominal voltage rating of 120 volts AC, with an acceptable input range of 0 to 132 volts AC. The IC200MDL243 input module has a 70 to 132 volt AC on-state operating range with a maximum response time of 1 cycle. The IC200MDL243 input module has 16 leds to indicate the status of each input point, and a status LED to show the working status of the backplane.

IC200MDL243 输入模块 交流现场设备

【其他型号推荐】