IC200MDL241 离散输入模块   16 通道离散输入模块

【产品详情】

GE Fanuc IC200MDL241 用于 Versamax I/O 和控制系统的离散输入模块。该模块有 16 个非隔离输入，分为 2 组，每组 8 个输入，具有 240 伏交流工作电压和 110 毫安的最大背板电流消耗。

GE Fanuc IC200MDL241 离散输入模块是用于 Versamax I/O 和控制系统的 16 通道离散输入模块。该 16 点输入模块接收来自交流输入设备的信号，并将其传输到公共端进行处理。来自按钮、传感器、开关和其他输入设备的信号作为 2 态离散信号（开/关）接收，并作为 16 位离散输入数据传输给 CPU 模块，以进行智能处理。IC200MDL241 输入模块采用紧凑型设计，提供与大型 PLC 中常见的灵活且经济高效的 I/O 解决方案。IC200MDL241输入模块安装在支持 DIN 导轨的 I/O 载体底座上，带有咬接式端子，有助于简化现场接线并支持热插拔。

IC200MDL241输入模块提供 16 个非隔离逻辑/源输入，分为 2 组，每组 8 个通道。IC200MDL241输入模块从背板获取所有电源，不需要用户提供的电源模块。它在 110.0 伏电压下从背板汲取 5.0 毫安的最大工作电流。它的额定工作电压为 240 伏交流电（标称值），工作电压范围为 0 至 264 伏交流电。 它还具有 155 伏交流电至 264 伏交流电的导通状态工作电压范围和 0 至 40 伏交流电的关断状态电压范围。IC200MDL241 输入模块没有点对点隔离，但每组之间具有 1500 伏的最大隔离 1 分钟。IC200MDL241 输入模块具有 1 个指示背板操作的 LED 和 16 个单独标记的 LED，用于指示每个输入点的状态。IC200MDL241 输入模块的模块尺寸约为 4.3 x 2.63 x 1.9 英寸。

IC200MDL241 是一个具有 16 个点的 VersaMax 交流输入模块。 该特定的分立式输入模块具有正逻辑或源极类型的输入。这意味着它们将从交流输入设备接收电流，然后返回公共端的电流。为此，输入设备连接在输入端子和公共端子之间。该IC200MDL241提供 16 位离散输入数据。该模块的电源来自背板，智能处理由 CPU 或 NIU 执行。每个模块都标配 LED 指示灯，用于指示输入上每个点的开/关状态，以及用于背板电源的 OK 指示灯。

安装 IC200MDL241 模块时，请务必仔细检查模块的各个方面。如果发现损坏，请记下并要求更换零件。将损坏的设备放入 CPU 可能会导致问题，并可能给用户带来进一步的问题。接线照片和说明可在线获得。用户应注意，如果热插入不当，同一背板上其他模块的工作可能会中断。安装人员还应该知道，如果使用高达 16 VAC 的电压，则 240 点模块不需要降额，但在 240 VAC 以上，同时开启的点数取决于环境温度和外部电压tage.

对于隔离，用户对逻辑和框架接地的输入为250 VAC连续或1500 VAC一分钟。该模块的输入电压为 0 至 264 VAC，标称值为 240 VAC。这包括最大 1 个周期的开启响应时间和最大 <> 个周期的关闭响应时间。安装人员应注意，该模块存在爆炸危险，不应更换任何组件。

IC200MDL241 离散输入模块   16 通道离散输入模块

【英文介绍】

The GE Fanuc IC200MDL241 is a discrete input module for Versamax I/O and control systems. The module has 16 non-isolated inputs, divided into 2 groups of 8 inputs each, with 240 volts AC operating voltage and a maximum backplane current consumption of 110 mA.

The GE Fanuc IC200MDL241 discrete input module is a 16-channel discrete input module for Versamax I/O and control systems. The 16-point input module receives the signal from the AC input device and transmits it to the common end for processing. Signals from buttons, sensors, switches, and other input devices are received as 2-state discrete signals (on/off) and transmitted to the CPU module as 16-bit discrete input data for intelligent processing. The IC200MDL241 input module is a compact design that provides a flexible and cost-effective I/O solution common in large PLCS. The IC200MDL241 input module is mounted on a DIN rail supported I/O carrier base with bite terminals to help simplify field wiring and support hot swapping.

The IC200MDL241 input module provides 16 non-isolated logical/source inputs divided into 2 groups of 8 channels each. The IC200MDL241 input module obtains all power supplies from the midplane and does not require a power module provided by the user. It draws a maximum operating current of 5.0 mA from the backplane at 110.0 volts. It has a rated operating voltage of 240 volts AC (nominal value) and an operating voltage range of 0 to 264 volts AC. It also has an on-state operating voltage range of 155 volts AC to 264 volts AC and an off state voltage range of 0 to 40 volts AC. The IC200MDL241 input module has no point-to-point isolation, but has a maximum isolation of 1500 volts between each group for 1 minute. The IC200MDL241 input module has 1 LED indicating backplane operation and 16 individually labeled leds indicating the status of each input point. The module size of the IC200MDL241 input module is approximately 4.3 x 2.63 x 1.9 inches.

The IC200MDL241 is a VersaMax AC input module with 16 points. This particular discrete input module has a positive logic or source type input. This means that they will receive current from the AC input device and then return the current to the common end. For this purpose, the input device is connected between the input terminal and the common terminal. The IC200MDL241 provides 16-bit discrete input data. The power supply of the module comes from the backplane, and intelligent processing is performed by the CPU or NIU. Each module comes standard with an LED indicator indicating the on/off status of each point on the input, as well as an OK indicator for the backplane power supply.

When installing the IC200MDL241 module, carefully check all aspects of the module. If you find damage, note it and ask for replacement parts. Putting a damaged device into the CPU can cause problems and may cause further problems for the user. Wiring photos and instructions are available online. Users should be aware that if the hot insertion is not proper, the work of other modules on the same backplane may be interrupted. Installers should also be aware that a 240 point module does not need derating if a voltage of up to 16 VAC is used, but the number of points opened at the same time above 240 VAC depends on the ambient temperature and external voltage tage.

For isolation, the user's input to the logic and frame grounding is 250 VAC continuously or 1500 VAC for one minute. The input voltage of the module is 0 to 264 VAC and the nominal value is 240 VAC. This includes an on response time of up to 1 cycle and a off response time of up to <> cycles. Installers should be aware that this module poses an explosion hazard and should not replace any components.

IC200MDL241 离散输入模块   16 通道离散输入模块

【其他型号推荐】