IC200MDL144 交流输入模块 离散输入模块

【产品详情】

GE Fanuc IC200MDL144 4 通道离散输入模块是专为 Versamax 系统设计的交流输入模块。该模块将交流输入模块与 VersmMax 紧凑型处理器模块连接起来。IC200MDL144输入模块以 2 态格式接收来自输入设备（如按钮、传感器和开关）的输入信号，并将这些信号作为 4 位离散型输入数据传输到 CPU 进行处理。IC200MDL144输入模块围绕 Versamax 紧凑型模块化蓝图设计，为用户提供应用灵活性，帮助降低工程和应用成本。IC200MDL144 输入模块可以安装在具有卡入功能的 Versamax 托架底座上，这有助于减少额外的布线并支持热插拔。

IC200MDL144 是一个 240 VAC 隔离输入模块，具有四个隔离模块。 该分立式输入模块提供四个隔离式分立式输入，每个模块输入使用正逻辑或源极型输入。它们从交流输入设备接收电流，然后在使用时返回公共端的电流。输入设备通过输入端子和公共端子连接。IC200MDL144模块的电源来自背板，智能处理由 NIU 或 CPU 执行。与许多模块一样，该模块提供 LED 来指示开/关状态和背板电源的存在。

此特定模块需要具有修订版 B 或更高版本的箱式、屏障式或弹簧式托架。该IC200MDL144不能与连接器式载体一起使用。模块上的隔离在用户输入到逻辑和帧接地时设置为连续 250 VAC，一分钟 1500 VAC。这包括 250 VAC 连续点对点和 1500 VAC 一分钟。5V的背板电流消耗稳定在30mA。此外，输入电压设置为 0 至 264 VAC 或 240 VAC 标称值。

在安装IC200MDL144之前，应仔细检查每个组件是否损坏。如果模块有任何损坏，应立即订购更换。另请注意，不正确的热插入可能会损坏或破坏背板上的其他模块。

IC200MDL144 输入模块具有 4 个独立隔离的离散输入，可以是正逻辑输入或源极输入。IC200MDL144从背板电源获取电源，不支持外部用户电源。IC200MDL144 输入模块的输入额定值为 240 伏交流电，0 至 264 伏交流电的工作范围为 47 至 63 赫兹。它在 30.5 V 时的最大背板额定电流为 0 毫安，最大导通状态电流额定值为 7.0 毫安。IC200MDL144 输入模块具有 2000 伏交流电点对点隔离 1 分钟，输入和接地之间具有 500 伏交流连续电压。IC200MDL144 输入模块在开启状态下具有 155 至 264 伏交流电的工作电压，在关闭状态下具有 0 至 40 伏交流电的工作电压。IC200MDL144 输入模块有 4 个单独标记的前面板 LED，用于指示每个输入点的开/关状态，以及 1 个背板 LED 状态指示灯。

IC200MDL144 交流输入模块 离散输入模块

【英文介绍】

The GE Fanuc IC200MDL144 4-channel discrete input module is an AC input module specifically designed for Versamax systems. The module connects the AC input module with the VersmMax compact processor module. The IC200MDL144 input module receives input signals from input devices (such as buttons, sensors, and switches) in a 2-state format and transmits these signals as 4-bit discrete input data to the CPU for processing. The IC200MDL144 input module is designed around the Versamax compact modular blueprint, providing users with application flexibility to help reduce engineering and application costs. The IC200MDL144 input module can be mounted on the Versamax bracket base with a snap-in function, which helps reduce additional wiring and supports hot swapping.

The IC200MDL144 is a 240 VAC isolated input module with four isolation modules. The discrete input module provides four isolated discrete inputs, each using positive logic or source type inputs. They receive current from AC input devices and then return current from the common end when in use. The input device is connected to the common terminal through the input terminal. The power supply of the IC200MDL144 module comes from the backplane, and the intelligent processing is performed by NIU or CPU. Like many modules, this module provides leds to indicate the on/off status and the presence of backplane power.

This particular module requires a box, screen or spring bracket with revision B or higher. The IC200MDL144 cannot be used with connector carriers. The isolation on the module is set to 250 VAC continuously and 1500 VAC per minute when the user inputs into the logic and frames are grounded. This includes 250 VAC continuous point-to-point and 1500 VAC one minute. The backplane current consumption of 5V is stable at 30mA. In addition, the input voltage is set to a nominal value of 0 to 264 VAC or 240 VAC.

Before installing the IC200MDL144, each component should be carefully checked for damage. If there is any damage to the module, order a replacement immediately. Also note that incorrect hot insertion may damage or destroy other modules on the backplane.

The IC200MDL144 input module has four independently isolated discrete inputs, which can be positive logic inputs or source inputs. The IC200MDL144 obtains power from the backplane power supply and does not support external power supplies. The IC200MDL144 input module has an input rating of 240 volts AC and an operating range of 47 to 63 Hz for 0 to 264 volts AC. It has a maximum backplane current rating of 0 mA at 30.5 V and a maximum on-state current rating of 7.0 MA. The IC200MDL144 input module has 2000 V AC point-to-point isolation for 1 minute and 500 V AC continuous voltage between input and ground. The IC200MDL144 input module has an operating voltage of 155 to 264 volts AC when on and 0 to 40 volts AC when off. The IC200MDL144 input module has four individually marked front panel leds to indicate the on/off status of each input point, and a backplane LED status indicator.

【其他型号推荐】