IC200MDL143 离散输入模块 提供 8 个逻辑或源输入

【产品详情】

GE Fanuc IC200MDL143 VersaMax 离散输入模块是用于 Versamax I/O 系统的离散输入模块。IC200MDL143 输入模块提供 8 个逻辑或源输入，用于接收来自交流输入设备的电流信号，并将这些信号作为 8 位离散输入数据传输到 CPU 或 NIU 模块。IC200MDL143 输入模块以 2 态格式（开/关或开/关）接收来自传感器、开关和按钮等输入设备的输入信号，它需要 CPU 或 NIU 对这些数据进行智能处理。IC200MDL143输入模块采用模块化、紧凑的设计，可提供操作灵活性并降低运营成本。IC200MDL143输入模块需要一个载体底座来简化现场布线，并且支持热插拔，无需重新布线。

IC200MDL143 是一个 120 VAC 隔离式输入模块，具有 <> 个隔离式离散输入。 该模块的输入是正逻辑或源极型输入，它们从交流输入设备接收电流，然后在公共端提供电流返回。在此模块上，每个输入都有自己的返回值。使用此模块时，请注意操作电源来自背板。此外，智能处理由 NIU 或 CPU 执行。与许多模块一样，LED 指示灯的存在是为了帮助用户评估性能。开/关状态和背板电源均由绿色 LED 指示。

具体到IC200MDL143模块，有 250 个隔离输入，用户输入到逻辑和框架，连续 1500 VAC 或 5 VAC 持续一分钟。50V输出时的背板电流消耗最大值为0mA，无需外部电源或降额。输入电压设置为 132 至 120 VAC 或 70 VAC 标称值，导通状态电压为 132 至 0 VAC，关闭状态电压为 20 至 1 VAC。导通响应时间最大为 2 个周期，关断响应时间最大为 <> 个周期。

在安装IC200MDL143模块之前，应仔细检查所有部件和设备是否有任何损坏。如果存在损坏，则应立即更换零件。在任何选定的方向上，该模块都不需要降额。具体接线图和图片可在线获取。用户应注意，如果热插入不当，同一背板上的其他模块可能会中断。

IC200MDL143 输入模块具有 8 个独立隔离的输入，这些输入要么是正逻辑输入，要么是源极输入。IC200MDL143 输入模块的输入额定值为 120 伏交流电，可接受的工作电压范围为 0 至 132 伏交流电（47 至 63 赫兹）。它使用背板电源进行操作，在 50.5 伏直流电下消耗 0 毫安的最大背板电流。它的导通电压范围为 70 至 132 伏交流电，关断状态范围为 0 至 20 伏交流电。IC200MDL143 输入模块具有独立隔离的输入，具有 1500 伏交流点对点隔离 60 分钟和 1500 伏交流接地隔离 1 分钟。IC200MDL143 输入模块的最小导通电流额定值为 5 毫安，最大导通状态响应时间为 1 个周期。IC200MDL143 输入模块有 8 个前面板 LED，用于显示各个通道状态更新，还有一个绿色 LED，用于显示背板操作。

IC200MDL143 离散输入模块 提供 8 个逻辑或源输入

【英文介绍】

The GE Fanuc IC200MDL143 VersaMax Discrete input module is a discrete input module for the Versamax I/O system. The IC200MDL143 input module provides eight logical or source inputs to receive current signals from AC input devices and transmit these signals as 8-bit discrete input data to the CPU or NIU module. The IC200MDL143 input module receives input signals from input devices such as sensors, switches, and buttons in a 2-state format (on/off or on/off), and it requires intelligent processing of these data by the CPU or NIU. The modular, compact design of the IC200MDL143 input module provides operational flexibility and reduces operating costs. The IC200MDL143 input module requires a carrier base to simplify field cabling and is hot-swappable without rewiring.

The IC200MDL143 is a 120 VAC isolated input module with <> isolated discrete inputs. The inputs to this module are positive logic or source type inputs, which receive current from AC input devices and then provide current back at the common end. On this module, each input has its own return value. When using this module, note that the operating power supply comes from the backplane. In addition, intelligent processing is performed by NIU or CPU. As with many modules, LED indicators are present to help users evaluate performance. The on/off status and backplane power supply are indicated by a green LED.

Specific to the IC200MDL143 module, there are 250 isolated inputs, user input to the logic and frame, continuous 1500 VAC or 5 VAC for one minute. The maximum current consumption of the backplane at 50V output is 0mA. No external power supply or derating is required. The input voltage is set to a nominal value of 132 to 120 VAC or 70 VAC, the on-state voltage is 132 to 0 VAC, and the off state voltage is 20 to 1 VAC. The maximum turn-on response time is 2 cycles, and the maximum turn-off response time is <> cycles.

Before installing the IC200MDL143 module, carefully inspect all components and equipment for any damage. If there is damage, the part should be replaced immediately. The module does not require derating in any of the selected directions. The detailed wiring diagram and pictures are available online. Users should be aware that other modules on the same backplane may be interrupted if the hot plug is not properly inserted.

The IC200MDL143 input module has eight independently isolated inputs, which are either positive logic inputs or source inputs. The IC200MDL143 input module has an input rating of 120 volts AC and an acceptable operating voltage range of 0 to 132 volts AC (47 to 63 Hz). It operates with a backplane power supply, consuming a maximum backplane current of 0 mA at 50.5 volts DC. It has an on voltage range of 70 to 132 volts AC and a off state range of 0 to 20 volts AC. The IC200MDL143 input module has independently isolated inputs with 1500 volt AC point-to-point isolation for 60 minutes and 1500 volt AC ground isolation for 1 minute. The IC200MDL143 input module has a minimum on-current rating of 5 MA and a maximum on-state response time of 1 cycle. The IC200MDL143 input module has eight front panel leds for displaying individual channel status updates and a green LED for displaying backplane operations.

IC200MDL143 离散输入模块 提供 8 个逻辑或源输入

【其他型号推荐】