IC200MDL141 交流输入模块  具有正逻辑或源极类型的输入

【产品详情】

IC200MDL141 是具有 <> 个点的 VersaMax 交流输入模块。 该特定的分立式输入模块具有正逻辑或源极类型的输入。这意味着它们将从交流输入设备接收电流，然后返回公共端的电流。为此，输入设备连接在输入端子和公共端子之间。

该IC200MDL141提供一组 <> 个离散输入。此特定模块的电源来自背板，并由 CPU 或 NIU 执行智能处理。每个模块都标配 LED 指示灯，显示输入端每个点的开/关状态，以及用于显示背板电源位置的 OK 指示灯。

安装前，应仔细检查IC200MDL141模块。如果发现损坏，请更换损坏的部件。请勿使用损坏的部件或将损坏的部件放入 CPU。用户还应注意正确热插入的重要性，以避免干扰同一背板上的其他模块。注意：无论方向如何，8 点模块都不需要降额。对于隔离，用户对逻辑和框架接地的输入为250 VAC连续或1500 VAC一分钟。该模块的输入电压为 0 至 254 VAC，标称值为 240 VAC，包括最大 1 个周期的导通响应时间和最大 <> 个周期的关断响应时间。该模块具有爆炸危险;因此，不应替换任何组件。

IC200MDL141 离散输入模块是 GE Fanuc Versamax I/O 和控制系统的 8 通道离散输入模块。Versamax I/O 系统采用模块化设备，通过内置诊断功能、热插入支持和简化接线提供灵活性和易用性，有助于降低接线成本。IC200MDL141 输入模块通过将 2 态信号（开/关或开/关）从这些输入设备作为离散信号传输到 CPU，在输入设备（如按钮、传感器和开关）和 CPU 模块之间提供接口。IC200MDL141 输入模块围绕 Versamax 模块化蓝图构建，可在单个紧凑型系统中提供直观的诊断、自动模块配置和热模块插入。

IC200MDL141 输入模块安装在卡扣式 I/O 载体底座上，提供接线灵活性。IC200MDL141输入模块有 8 个非隔离式正逻辑/源极输入，排列成一组 8 个。该模块需要背板电源才能运行，不支持或不需要外部电源。IC200MDL141 输入模块的标称输入额定值为 240 伏交流电，工作电压范围为 0 至 264 伏交流电，频率为 47 至 63 赫兹。它在 55 伏直流电下的最大背板额定电流为 5 毫安，最小额定电流为每点 7.0 毫安。IC200MDL141 输入模块的最大导通状态响应时间为 1 个周期，隔离额定值为 1500 伏交流电，持续 1 分钟，在用户输入与逻辑（光纤）和框架接地之间持续 200 分钟。IC141MDL8 输入模块有 1 个单独编号的 LED 和 <> 个状态 LED，分别显示输入点状态和背板状态。

IC200MDL141 交流输入模块  具有正逻辑或源极类型的输入

【英文介绍】

The IC200MDL141 is a VersaMax AC input module with <> points. This particular discrete input module has a positive logic or source type input. This means that they will receive current from the AC input device and then return the current to the common end. For this purpose, the input device is connected between the input terminal and the common terminal.

The IC200MDL141 provides a set of <> discrete inputs. The power for this particular module comes from the backplane and is processed intelligently by the CPU or NIU. Each module comes standard with an LED indicator indicating the on/off status of each point in the input, as well as an OK indicator indicating the power position of the backplane.

Before installing the IC200MDL141, carefully check the IC200MDL141. If damaged, replace the damaged parts. Do not use damaged parts or put damaged parts into the CPU. Users should also note the importance of proper hot insertion to avoid interfering with other modules on the same backplane. Note: Regardless of orientation, the 8-point module does not require derating. For isolation, the user's input to the logic and frame grounding is 250 VAC continuously or 1500 VAC for one minute. The module has an input voltage of 0 to 254 VAC and a nominal value of 240 VAC, including an on-off response time of up to 1 cycle and a turn-off response time of up to <> cycles. The module has an explosion hazard; Therefore, no component should be replaced.

The IC200MDL141 discrete input module is an 8-channel discrete input module for GE Fanuc Versamax I/O and control systems. The Versamax I/O system is modular and offers flexibility and ease of use with built-in diagnostics, hot-plug support and simplified wiring, helping to reduce wiring costs. The IC200MDL141 input module provides an interface between input devices (such as buttons, sensors, and switches) and the CPU module by transmitting 2-state signals (on/off or on/off) from these input devices to the CPU as discrete signals. Built around the Versamax modular blueprint, the IC200MDL141 input module provides intuitive diagnostics, automatic module configuration, and hot module insertion in a single compact system.

The IC200MDL141 input module is mounted on a snap-on I/O carrier base to provide wiring flexibility. The IC200MDL141 input module has 8 non-isolated positive logic/source inputs arranged in a group of 8. The module requires a backplane power supply to operate and does not support or require an external power supply. The IC200MDL141 input module has a nominal input rating of 240 volts AC and an operating voltage range of 0 to 264 volts AC and a frequency of 47 to 63 Hertz. It has a maximum backplane rating of 5 mA at 55 volts DC and a minimum rating of 7.0 mA per point. The IC200MDL141 input module has a maximum on-state response time of 1 cycle with an isolation rating of 1500 volts AC for 1 minute and a duration of 200 minutes between user input and logic (fiber) and frame ground. The IC141MDL8 input module has one individually numbered LED and <> status LED to display the input point status and backplane status respectively.

IC200MDL141 交流输入模块  具有正逻辑或源极类型的输入

【其他型号推荐】