IC200MDD847 混合 I/O 模块 具有混合输入和输出

【产品详情】

IC200MDD847是由GE Fanuc制造的具有混合输入和输出的VersaMax模块。 该模块总共能够支持 16 个输入和输出点，其中 <> 个是分立式正逻辑或源输入点，其余 <> 个是 A 型继电器输出点。每个输出点在通道间单独隔离;但是，该模块不使用缓冲器或内部保险丝来保护每个输入和输出点。每个继电器输出点能够驱动高达 <> 安培的功率。该器件支持 <> 位离散输入和输出数据，但此处理必须由 CPU 或 NIU 执行。该模块不支持热降额。

该器件的电源从 5 伏背板接收，该器件从该背板消耗的最大电流为 300 毫安。从电源汲取的电流将与激活的输出点的数量成比例地增加。当连接的设备处于“开启”状态时，电流至少为 4 毫安，而处于“关闭”状态的设备的电流最多为 1.5 毫安。该模块的输入“开启”状态电压为 155 至 264 伏交流电，输入“关闭”状态电压范围为 0 至 40 伏交流电。

以下是IC200MDD847的物理规格：高度为 2.63 英寸，或 66.8 毫米;宽度为 4.3 英寸，或 110 毫米;深度为 1.956 英寸，或 50 毫米。载体和连接器的物理特性不包括在这些测量中。

GE Fanuc IC200MDD847 混合 I/O 模块是 GE Fanuc 的产品。它属于 Versamax 系列，具有混合输入和输出，支持多达 16 个 I/O 点。其中 8 个 I/O 点是分立式正逻辑输入类型或源极型输入点，而其余 200 个 I/O 点是 A 型继电器型输出点。此模块上的每个输出点在通道间单独分离，但IC847MDD2模块不支持使用内部保险丝或缓冲器来保护每个输出和输入点。每个继电器输出点可以驱动 8 安培的电流。它还支持 <> 位离散 I/O 数据。但是，处理必须由 CPU 或网络接口单元执行。该模块不支持热降额选项。

IC200MDD847混合 I/O 模块从额定电压为 5 伏的背板电源接收电源，并由此消耗 300 毫安的最大电流。它从电源汲取的电流根据激活的输出点总数而增加。当 IC200MDD847 模块连接的设备处于开启状态时，它的最小电流为 4 毫安，当连接的设备处于关闭状态时，它的最小电流为 1.5 毫安。开启状态下的输入电压范围为 155 至 264 伏交流电，而处于关闭状态的电压范围为 0 至 40 伏交流电。该模块的近似尺寸为 2.63 x 4.3 x 1.956 英寸，但这些测量值不包括连接器和载体的物理尺寸。

IC200MDD847 混合 I/O 模块 具有混合输入和输出

【英文介绍】

The IC200MDD847 is a VersaMax module with mixed input and output manufactured by GE Fanuc. The module can support A total of 16 input and output points, of which <> are separate positive logic or source input points, and the remaining <> are A-type relay output points. Each output point is isolated separately between channels; However, the module does not use a buffer or internal fuse to protect each input and output point. Each relay output point is capable of driving power up to <> amps. The device supports <> bit discrete input and output data, but this processing must be performed by the CPU or NIU. The module does not support hot derating.

The device's power supply is received from a 5-volt backplane, from which the device consumes a maximum current of 300 mA. The current drawn from the power supply will increase in proportion to the number of active output points. When the connected device is in the "on" state, the current is at least 4 mah, and when the device is in the "off" state, the current is up to 1.5 mah. The input "On" state voltage of the module is 155 to 264 volts AC, and the input "off" state voltage range is 0 to 40 volts AC.

The following are the physical specifications of the IC200MDD847: The height is 2.63 inches, or 66.8 mm; A width of 4.3 inches, or 110 mm; The depth is 1.956 inches, or 50 millimeters. The physical characteristics of the carrier and connector are not included in these measurements.

GE Fanuc IC200MDD847 Hybrid I/O module is a product of GE Fanuc. It belongs to the Versamax family, has mixed inputs and outputs, and supports up to 16 I/O points. Eight of the I/O points are separate positive logic input types or source input points, while the remaining 200 I/O points are Type A relay output points. Each output point on this module is separated separately between channels, but the IC847MDD2 module does not support the use of internal fuses or buffers to protect each output and input point. Each relay output point can drive 8 amps of current. It also supports <> bit discrete I/O data. However, the processing must be performed by the CPU or network interface unit. The module does not support hot derating.

The IC200MDD847 hybrid I/O module receives power from a backplane power supply rated at 5 volts and thus consumes a maximum current of 300 mA. The current it draws from the power supply increases according to the total number of active output points. The IC200MDD847 module has a minimum current of 4 MA when the device connected to it is on and 1.5 MA when the device connected to it is off. The input voltage range is 155 to 264 volts AC in the On state and 0 to 40 volts AC in the off state. The approximate dimensions of the module are 2.63 x 4.3 x 1.956 inches, but these measurements do not include the physical dimensions of the connector and carrier.

IC200MDD847 混合 I/O 模块 具有混合输入和输出

【其他型号推荐】