IC200DBI001 远程输入/输出 网络接口单元

【产品详情】

GE Fanuc IC200DBI001 是一款远程输入/输出 （I/O） DeviceNet 网络接口单元。 DeviceNet支持多种通信结构，如多主站、点对点和具有广播功能的主/从站。多达 64 个节点能够连接到 DeviceNet 网络，而无需路由或桥接。

IC200DBI001 NIU 实际上是一个 DeviceNet 从站模块，用作 VersaMax 模块的输入/输出 （I/O） 站的控制器。I/O 站中 I/O 模块的操作以其默认设置的特性进行。多种模块类型可以组合使用，以满足应用要求。

该模块的运行由电源供电，该电源直接安装在 NIU 上。对于具有更高电流需求的模块，可以在需要时向系统添加额外的“升压”电源。

IC200DBI001 NIU 每个工作站有 8 个 I/O 模块，可处理多达 128 字节的输入和 128 字节的输出数据。它具有仅第 2 组服务器和两种 I/O 类型：状态更改和轮询。其数据速率由模块的开关设置，可以是 125K、250K 或 500K。 电源 LED 指示灯指示是否有电。NIU的功耗在160V时为5mA，在10.3V时为3mA。

要安装它，首先将其卡入DIN导轨上的位置。通过将电源锁定在 NIU 上的解锁位置来继续安装其电源。然后将闩锁转到锁定位置。完整的电源接线。

接下来，使用扁平的 2.44 毫米螺丝刀调整 NIU 前面的旋转开关。继续将通信总线连接到 NIU 的前连接器。然后取下 NIU 右侧的连接器盖。将其他模块安装在其托架上并启动 NIU。确保观察模块的 LED 指示灯，这些指示灯指示是否通电。

LED指示灯：

如果 LED 指示灯上的 PWR 灯呈绿色亮起，则表示已通电。绿色 OK 灯代表可操作的 NIU。FAULT 以琥珀色亮起，以防 NIU 检测到故障。

NIU 未通电时 MOD 不亮;NIU 配置不正确或缺失时闪烁;绿色表示正常运行;可恢复故障时闪烁红色;不可恢复故障时闪烁红色。在后一种情况下，可能需要更换 NIU。

NIU 未通电时 NET 不亮;当 NIU 检测到网络访问错误时闪烁绿色和红色;当 NIU 处于联机状态且未连接到其他节点且未分配给主节点时，呈绿色闪烁;联机时呈绿色常亮并分配给主站;如果 1+ I/O 连接超时，则闪烁红色;如果 NIU 无法与网络通信，则红色常亮。

FORCE 指示任何强制 I/O 值。它始终处于关闭状态。

IC200DBI001 远程输入/输出 网络接口单元

【英文介绍】

The GE Fanuc IC200DBI001 is a remote input/output (I/O) DeviceNet network interface unit. DeviceNet supports a variety of communication structures such as multi-master, point-to-point, and master/slave stations with broadcast capabilities. Up to 64 nodes are able to connect to the DeviceNet network without routing or bridging.

The IC200DBI001 NIU is actually a DeviceNet slave station module that acts as a controller for the input/output (I/O) station of the VersaMax module. The operation of the I/O module in the I/O station is performed with its default Settings. Multiple module types can be combined to meet application requirements.

The operation of the module is powered by a power supply, which is installed directly on the NIU. For modules with higher current requirements, additional "boost" power supplies can be added to the system when needed.

IC200DBI001 NIU Each workstation has 8 I/O modules that can handle up to 128 bytes of input and 128 bytes of output data. It has only group 2 servers and two types of I/O: status change and polling. The data rate is set by the switch of the module and can be 125K, 250K or 500K. Power LED indicator indicates whether power is available. The power consumption of NIU is 5mA at 160V and 3mA at 10.3V.

To install it, first clamp it into position on the DIN rail. Continue installing its power supply by locking it in the unlocked position on the NIU. Then turn the latch to the lock position. Complete power wiring.

Next, adjust the rotary switch on the front of the NIU using a flat 2.44mm screwdriver. Continue connecting the communication bus to the front connector of NIU. Then remove the connector cover on the right side of the NIU. Install the other modules on its carrier and start NIU. Make sure to observe the module's LED indicators, which indicate whether or not power is on.

LED indicator:

If the PWR light on the LED indicator is green, it means that power is on. A green OK light indicates an operational NIU. FAULT lights up amber in case NIU detects a fault.

The MOD is off when NIU is not powered on. Blinking when NIU is incorrectly configured or missing. Green indicates normal operation; Blinking red when a recoverable fault occurs; Blinking red when an unrecoverable fault occurs. In the latter case, the NIU may need to be replaced.

NET is not on when NIU is not powered on. NIU blinks green and red when it detects a network access error. When the NIU is online, is not connected to another node, and is not assigned to the active node, the NIU is blinking green. When online, it is steady green and assigned to the main station; If the 1+ I/O connection times out, it flashes red. If NIU cannot communicate with the network, it is steady red.

FORCE Indicates any forced I/O value. It is always closed.

IC200DBI001 远程输入/输出 网络接口单元

【其他型号推荐】