IC200BEM103 网络通信模块 连接器进行连接

【产品详情】

技术规格

模块类型： 网络通信模块

站点数量： 不适用

I/O 数据： 高达 128 字节的输入和输出

连接器： 5 针开放式可插拔

网络数据速率： 125 Kbaud、250 Kbaud 或 500 Kbaud

功耗： 490 mA（5 V 输出）

GE IC200BEM103模块是一个网络接口模块。它可以支持多达 128 字节的输入和输出数据。它使用 5 针开放式连接器进行连接。该模块支持 125、250 和 500 Kbaud 的不同数据速率。背板的 140 V 输出消耗 5 毫安的电流，DeviceNet 的最大消耗电流为 125 毫安。该模块能够与其他网络交换 512 字节的输入和输出数据。网络模块一次最多可支持40个从设备。在安装过程中，模块中的闩锁应处于解锁位置。连接器和闩锁应对齐并推动，直到发出咔嗒声。该模块允许连接 64 个节点，而无需桥接。

IC200BEM103模块设计用于在 I 类 2 级环境中运行。该模块不支持冗余设置。它使用 24 伏直流电压为节点设备的网络供电。IC200BEM103模块的前面板上带有 LED 指示灯，当发生通信活动时会亮起。它有一个“OK”LED、“MOD”LED 和一个“NET”LED 指示灯，用于在 DeviceNet 网络上进行通信。它以 3 种不同的模式运行。该模块可以配置为通用通信模块。IC200BEM103模块具有重复地址检测功能。该模块的数据大小介于 0 到 8 字节之间，用于消息碎片。正常运行时，环境温度应设置在 0 至 60 摄氏度之间。它使用屏蔽对电缆，中间有引线，引线有 19 股。

客户问答

问题：什么是IC200BEM103？答：IC200BEM103是GE Fanuc Versamax系列的PLC网络通信DeviceNet（主站）模块。

问： IC200BEM103为 Versamax 系统做了什么？ 答： 该模块在DeviceNet网络上作为主站运行。该模块还可以作为从站或同时作为主站和从站运行。

问：IC200BEM103与从设备有什么关系？ 答： 该模块可以交换 128 字节的输入数据和输出数据。多达 63 个附加设备，其中许多设备还通过此模块和电源驻留在网络上。在这些设备中，最多可以有 40 个是由 DeviceNet NCM 控制的从设备。

问题：IC200BEM103需要什么？ 答： IC200BEM103需要IC200CHS006通信运营商。

问： IC200BEM103的 LED 表示什么？答： LED 指示电源的存在并显示模块的网络通信状态。

 IC200BEM103 网络通信模块 连接器进行连接

【英文介绍】

Technical specification

Module type: Network communication module

Number of sites: Not applicable

I/O data: up to 128 bytes of input and output

Connector: 5-pin open pluggable

Network data rate: 125 Kbaud, 250 Kbaud or 500 Kbaud

Power consumption: 490 mA (5 V output)

GE IC200BEM103 is a network interface module. It can support up to 128 bytes of input and output data. It is connected using a 5-pin open connector. The module supports different data rates of 125, 250 and 500 Kbaud. The backplane's 140 V output consumes 5 mah, and the DeviceNet's maximum consumption is 125 mah. The module is capable of exchanging 512 bytes of input and output data with other networks. A network module can support up to 40 slave devices at a time. The latch in the module should be in the unlocked position during installation. Connectors and latches should be aligned and pushed until they click. This module allows 64 nodes to be connected without bridging.

The IC200BEM103 module is designed to operate in a Class I Level 2 environment. This module does not support redundancy Settings. It uses 24 volts DC to power the network of node devices. The IC200BEM103 module has an LED indicator on the front panel that lights up when communication activity occurs. It has an "OK" LED, a "MOD" LED, and a "NET" LED indicator for communication on the DeviceNet network. It operates in 3 different modes. This module can be configured as a general purpose communication module. The IC200BEM103 module has the function of duplicate address detection. The data size of this module is between 0 and 8 bytes and is used for message fragmentation. During normal operation, the ambient temperature should be set between 0 and 60 degrees Celsius. It uses a shielded pair of cables with a lead in the middle, and the lead has 19 strands.

Customer question and answer

Question: What is IC200BEM103? A: IC200BEM103 is a PLC network communication DeviceNet (master station) module of GE Fanuc Versamax series.

Q: What does IC200BEM103 do for the Versamax system? Answer: The module runs as a master station on the DeviceNet network. The module can also operate as a slave station or both as a master and slave station.

Q: What is the relationship between IC200BEM103 and the slave device? A: This module can exchange 128 bytes of input and output data. Up to 63 additional devices, many of which also reside on the network through this module and power supply. Of these devices, up to 40 can be slave devices controlled by DeviceNet NCM.

Question: What does IC200BEM103 need? Answer: IC200BEM103 requires the IC200CHS006 communication carrier.

Q: What does the LED of IC200BEM103 mean? A: The LED indicates the presence of the power supply and displays the network communication status of the module.

 IC200BEM103 网络通信模块 连接器进行连接

【其他型号推荐】