IC200ALG327 模拟输出模块 输出需要外部电源

【产品详情】

产品描述

IC200ALG327是GE Fanuc Versamax系列的12通道、13位电压模拟输出模块。该IC200ALG327配备 12 个模拟电压输出。输出电压范围为-10VDC至+10VDC（双极性），而模块的输出范围为0V至+10VDC（单极性）。

CPU或网络接口单元负责智能处理，输出需要外部电源。IC200ALG327模块配有用于状态观察的 LED 指示灯。当绿色 OK LED 亮起时，这表示用户背板电源当前正在流向 IC200ALG327 模块。IC200ALG327输出范围是默认的，要改变输出范围，请使用跳线。该模块还设置了一个跳线，以便在背板电源或通信中断时使输出保持其最后状态。

IC200ALG327模块输出将保持先前的状态，或者直到模块从背板接收到不同的输出数据，或者直到现场电源断开。位于载波上的跳线可用于选择输出范围和输出默认模式。如果引脚 B1 和 B2 上未连接跳线，则输出将按其默认范围进行组织。如果安装了跳线（仅当现场或背板电源被移除时才需要），则输出范围将发生变化。

技术规格

不。通道数： 12 个单端，一组

电压范围： +/- 10.24 VDC，0 至 +10 VDC

电流范围： 不适用

更新速率： 15 毫秒

LED指示灯： FLD 压水堆，OK

功耗： +50V 总线 5 mA

GE Fanuc Automation IC200ALG327输出模块需要用屏蔽电缆和屏蔽终端连接，以避免可能影响模块整体功能的各种干扰。当模块存在射频发射时，建议降低精度额定值以考虑发射。GE Fanuc Automation IC200ALG327输出模块的通道被分类为一组。电路之间不提供隔离，模块采用的电压为 18 至 30 伏直流电压，包括纹波。该模块的额定电流消耗最大值为 112 毫安。该模块可在最小 5000 欧姆的负载和 13 位的分辨率下运行。

IC200ALG327 模拟输出模块 输出需要外部电源

【英文介绍】

Product description

The IC200ALG327 is a 12-channel, 13-bit voltage analog output module of the GE Fanuc Versamax series. The IC200ALG327 is equipped with 12 analog voltage outputs. The output voltage ranges from -10VDC to +10VDC (bipolar), while the module's output ranges from 0V to +10VDC (unipolar).

The CPU or network interface unit is responsible for intelligent processing, and the output requires an external power supply. The IC200ALG327 module is equipped with an LED indicator for status observation. When the green OK LED lights up, it indicates that the user backplane power is currently flowing to the IC200ALG327 module. The IC200ALG327 output range is the default. To change the output range, use a jumper. The module also sets up a jumper to keep the output in its final state in the event of a loss of backplane power or communication.

The IC200ALG327 module output will remain in its previous state either until the module receives different output data from the backplane or until the field power supply is disconnected. The jumper located on the carrier can be used to select the output range and output default mode. If there are no jumpers attached to pins B1 and B2, the output is organized according to its default range. If a jumper is installed (which is only needed if the field or backplane power supply is removed), the output range will change.

Technical specification

Nooooo. Number of channels: 12 single-ended, one group

Voltage range: +/- 10.24 VDC, 0 to +10 VDC

Current range: Not applicable

Update rate: 15 ms

LED indicator: FLD PWR, OK

Power consumption: +50V bus 5 mA

GE Fanuc Automation IC200ALG327 output modules need to be connected with shielded cables and shielded terminals to avoid various interference that may affect the overall function of the module. When RF emission is present in the module, it is recommended to lower the accuracy rating to account for emission. The channels of GE Fanuc Automation IC200ALG327 output module are classified into a group. No isolation is provided between the circuits, and the modules use voltages of 18 to 30 volts DC, including ripple. The maximum rated current consumption of the module is 112 MA. The module can operate at a minimum load of 5000 ohms and a resolution of 13 bits.

IC200ALG327 模拟输出模块 输出需要外部电源

【其他型号推荐】