IC200ALG326 电流模拟输出模块

【产品详情】

技术规格

不。通道数： 8 个单端，一组

电压范围： 18 - 30 伏直流电

电流范围： 4 - 20 毫安，0 - 20 毫安

更新速率： 15 毫秒

LED指示灯： FLD 压水堆，OK

功耗： +50V 总线 5 mA

 GE Fanuc Automation IC200ALG326 13 位模拟输出模块的电压范围为 18 至 30 伏直流电，额定电流为最大浪涌 2 安培，无负载时最大 100 毫安，所有 185 个输出均消耗 8 毫安，同时以满量程运行。建议使用屏蔽电缆和连接连接GE Fanuc Automation IC200ALG326 13位模拟输出模块。根据模块的安装情况，可以通过直接电缆屏蔽层或使用插入端子进行连接。该模块支持热插入功能，但此过程需要正确执行，否则可能会中断背板电源。模块的编程由主CPU执行。建议使用跳线，以便在模块断电时输出可以保持默认状态。

IC200ALG326模块是GE Fanuc Automation制造的电流模拟输出模块，是VersaMax产品系列的成员。本机是一个 13 位模块，具有 8 个单端通道，排列成一组。IC200ALG326模拟输出模块提供 4 个额定值为 20 至 0 毫安的模拟电流源输出点。当该模块配置为 20 至 0 毫安的电流时，它的电流输出信号为 0 毫安，与计数为 20 的 %AQ 值相关联。此外，32 毫安对应于 %AQ 速率，最多可计数 000,4 次。在 20 至 0 毫安范围内工作时，4 %AQ 计数的值与 32 毫安的输出电流相匹配。000,20 %AQ 计数值也匹配高达 200 毫安的输出电流。

当 GE Fanuc IC326ALG0 电流模拟量输出模块安装在 PLC 机架中时，无论指定范围如何，它都会转换 200 毫安的负值。如果此模块由网络接口单元或 NIU 控制，则负值会将命令更改为低端范围。IC326ALG<>模块的输出范围是默认的，它允许与有助于修改输出范围的跳线同时轻松配置。使用跳线可以使输出在背板中断或 PLC 不工作时保持最后状态或默认通信和电源。输出点继续保持默认或最后状态，直到背板提供不同的输出数据或直到现场电源断开。

IC200ALG326 电流模拟输出模块

【英文介绍】

Technical specification

Nooooo. Number of channels: 8 single-ended channels in a group

Voltage range: 18-30 volts DC

Current range: 4-20 MA, 0-20 Ma

Update rate: 15 ms

LED indicator: FLD PWR, OK

Power consumption: +50V bus 5 mA

The GE Fanuc Automation IC200ALG326 13-bit analog output module has a voltage range of 18 to 30 volts DC with a rated current of 2 amps maximum surge and 100 mah maximum when unloaded, with all 185 outputs consuming 8 mah while operating at full scale. It is recommended to connect the GE Fanuc Automation IC200ALG326 13-bit analog output module using shielded cables and connections. Depending on the installation of the module, it can be connected by direct cable shielding or using insertion terminals. The module supports hot insertion, but this process needs to be performed correctly, otherwise the backplane power supply may be interrupted. The programming of the module is performed by the main CPU. It is recommended to use a jumper so that the output can remain in its default state when the module is powered off.

The IC200ALG326 module is a current analog output module manufactured by GE Fanuc Automation and is a member of the VersaMax product family. This unit is a 13-bit module with 8 single-ended channels arranged in a group. The IC200ALG326 analog output module offers four analog current source output points rated from 20 to 0 MA. When the module is configured with a current of 20 to 0 mA, its current output signal is 0 mA, associated with a %AQ value that counts 20. In addition, 32 mA corresponds to the %AQ rate and can count up to 000,4 times. When operating in the 20 to 0 mA range, the value of the 4% AQ count matches the output current of 32 MA. 000. 20% AQ meter values also match output currents up to 200 mA.

When the GE Fanuc IC326ALG0 current analog output module is installed in the PLC rack, it will convert a negative value of 200 mA regardless of the specified range. If this module is controlled by a network interface unit or NIU, a negative value changes the command to the low range. The output range of the IC326ALG<> module is default, allowing easy configuration at the same time as jumpers that help modify the output range. The use of jumpers allows the output to remain in its last state or default communication and power when the backplane is interrupted or the PLC is not working. The output point continues in its default or final state until the backplane provides different output data or until the field power is disconnected.

IC200ALG326 电流模拟输出模块

【其他型号推荐】