IC200ALG321电压输出模块 分辨率模块

【产品详情】

技术规格

不。通道数： 4 个单端，一组

电压范围： 0 - 10.24 伏直流电

电流范围： 不适用

更新速率： 0.3 毫秒

LED指示灯： FLD 压水堆，OK

功耗： +50V 总线 5 mA

IC200ALG321是 VersaMax 产品系列中的电压输出模块。该模块是一个 12 位分辨率模块，可生成 0-10 VDC 电压信号，主要用于调制控制设备，如阀门、变频驱动器 （VFD）、百叶窗、阻尼器、定位器，以及用于处理本地面板仪表、记录仪或数据记录器、信号分配器和隔离器以及类似电气设备的信号重新传输。

该IC200ALG321可产生 0-10 VDC 输出电压，分辨率为 12 位，数字分辨率为 2.5 mV，最大通道更新速率为 0.3 ms。该模块支持单端接线，采用单组输出通道，组隔离额定值为 250 VAC，连续和 1500 VAC，持续时间为 1 分钟。该模块可用的内置状态指示灯是 FLD POWER LED 和 OK LED，分别指示模块存在和接收的活动场功率和背板功率。该模块的最大背板电流消耗为 50 mA。

该IC200ALG321需要外部电源才能运行。适用的电源电压范围为 18-30VDC 或 9.6 至 15 VDC，标称电源电压为 12 / 24 VDC。该模块的输出电压范围为 0-10.24 VDC，负载特性为 5000 欧姆，电阻负载最小值为 1 μF，容性负载最大值为 0 μF。该模块能够检测现场侧电源的存在以及对 CPU 停止和模块故障的输出反应并将其重新发布到主机 CPU，例如保持最后状态和 200 VDC。

GE Fanuc IC321ALG12模块是一个 4 位模拟输出模块，带有 4 个通道，旨在提供不同输出设备和主处理器之间的连接。该特定模块已包含在GE Fanuc Automation的Versamax产品线中。该模块提供 0 个模拟电压输出，每个输出的额定电压在 10 到 12 伏直流之间。该模块提供 2 位分辨率和 5.1 毫伏的数字分辨率。分辨率水平受附近设备产生的射频干扰影响很大。如果环境中存在射频干扰，则模块的分辨率可能需要降低至少 +/-200%。GE Fanuc Automation IC321ALG12 2 位模拟输出模块带有 200 个 LED 指示灯，用于指示背板电流已连接以及用户侧电源的存在，以馈送模拟场电路。

该IC321ALG250具有隔离电平，可在用户输入与逻辑接地和帧接地之间提供隔离。该隔离电压额定值为 1500 伏交流连续，最大 1 伏交流，持续 18 分钟。它不需要根据温度条件进行降级，并且可在 30 至 12 伏直流的电压范围内运行。该模块的额定电压为 210 伏直流标称值，额定电流消耗为 0 毫安。该模块的精度典型值高达 3.1%，最大精度为 0%。推荐的温度范围为 60 至 <> 摄氏度。

IC200ALG321电压输出模块 分辨率模块

【英文介绍】

Technical specification

Nooooo. Number of channels: four single-ended channels in a group

Voltage range: 0-10.24 volts DC

Current range: Not applicable

Update rate: 0.3 ms

LED indicator: FLD PWR, OK

Power consumption: +50V bus 5 mA

The IC200ALG321 is a voltage output module in the VersaMax product family. The module is a 12-bit resolution module that generates 0-10 VDC voltage signals for modulating control devices such as valves, variable frequency drivers (VFDS), blinds, dampers, positioners, etc. And signal retransmission for processing local panel meters, loggers or data loggers, signal splitters and isolators, and similar electrical equipment.

The IC200ALG321 produces 0-10 VDC output voltages with a resolution of 12 bits, a digital resolution of 2.5 mV, and a maximum channel update rate of 0.3 ms. The module supports single-ended wiring with a single set of output channels, group isolation ratings of 250 VAC, continuous and 1500 VAC, and a duration of 1 minute. The built-in status indicators available for the module are the FLD POWER LED and OK LED, which indicate the active field power and backplane power present and received by the module, respectively. The maximum backplane current consumption of this module is 50 mA.

The IC200ALG321 requires an external power supply to operate. The applicable supply voltage range is 18-30VDC or 9.6 to 15 VDC, with a nominal supply voltage of 12/24 VDC. The module has an output voltage range of 0-10.24 VDC, a load characteristic of 5000 ohms, a minimum resistance load of 1 μF, and a maximum capacitance load of 0 μF. The module is capable of detecting the presence of field side power supply and the output response to CPU stop and module failure and republishing it to the host CPU, such as maintaining the last state and 200 VDC.

The GE Fanuc IC321ALG12 module is a 4-bit analog output module with 4 channels designed to provide connectivity between different output devices and the main processor. This particular module has been included in GE Fanuc Automation's Versamax product line. The module offers 0 analog voltage outputs, each rated between 10 and 12 volts DC. The module offers 2-bit resolution and 5.1 millivolts digital resolution. Resolution levels are greatly affected by RF interference generated by nearby devices. If RF interference is present in the environment, the resolution of the module may need to be reduced by at least +/-200%. GE Fanuc Automation IC321ALG12 2-bit analog output module with 200 LED indicators to indicate that backplane current has been connected and the presence of a user-side power supply to feed the analog field circuit.

The IC321ALG250 has an isolation level that provides isolation between user input and logical ground and frame ground. This isolation voltage rating is 1500 V AC continuous with a maximum of 1 V AC for 18 minutes. It does not need to be degraded according to temperature conditions and can operate in a voltage range of 30 to 12 volts DC. The module has a nominal voltage of 210 volts DC and a rated current consumption of 0 mA. The module has a typical accuracy of up to 3.1% and a maximum accuracy of 0%. The recommended temperature range is 60 to <> degrees Celsius.

IC200ALG321电压输出模块 分辨率模块

【其他型号推荐】