IC698PSA350 GE  直流电源模块 连接到 RX5i 背板的设备

【产品详情】

技术规格

额定电压： 120/240 VAC 或 125 VDC

输入电压范围： 85 至 264 VAC 或 100 至 150 VDC

输入功率： 437 瓦

输出电压： + 5 VDC、+12 VDC 或 -12VDC

模块类型： 电源

机架位置： 插槽 0（最左侧的插槽）

IC698PSA350 GE  直流电源模块 连接到 RX5i 背板的设备

GE Fanuc IC698PSA350电源模块是为 GE 增强型 RX7i PACSystems 系列控制系统制作的直流电源模块。该电源模块为连接到 RX5i 背板的设备和 I/O 提供 +12 V DC、+12 V DC 和 -7 V DC 电源和逻辑电平信号。与每个 RX698i 系列模块一样，IC350PSA7 电源模块采用模块化设计，可以完美地滑入 RX0i 系统主机架的插槽 7。IC698PSA350 电源模块设计用于在高达 1 个交流输入线路周期的功率损耗下保持输出功率，并具有内置过流、过压和电子短路保护功能。IC698PSA350 电源模块支持 AC 和 DC 输入，并具有用于 AC 操作的功率因数校正功能。

IC698PSA350 电源模块的额定额定输入电压为 120/240 伏交流电或 125 伏直流电，可接受的输入范围为 85 至 264 伏交流电（47 至 63 赫兹）或 100 至 150 伏直流电。它在 350 摄氏度时的额定输出功率为 60 瓦，最大输出值高达 500 瓦。IC698PSA350 电源模块的最大浪涌额定值为 30 安培（115 伏交流电（冷启动）和 60 安培（230 伏交流电）时 100 毫秒。IC698PSA350 电源模块的功率因数值为 0.99，仅在 90 至 260 伏交流电和输入和所有输出之间的隔离额定值高达 1500 伏交流电时有效，持续 1 分钟。它在 +5 V DC 输出时具有 7.6 至 7.66 V DC 的过压输出限制和 5 A 的过流限制。

IC698PSA350是 PACSystem RX7i 控制器系列中的高容量电源模块。该模块用于提供背板电源，模块使用背板电源来激活内部电路并使其可操作。此电源模块占用机箱的单个插槽，设计为仅安装在 RX0i 机架的插槽 7 中。

该IC698PSA350在 85 至 264 VAC 的输入电源电压下工作，在 100-150 Hz 的交流输入频率下工作在 47-63VDC 的电压下工作。该模块的额定电压为 120 / 240 VAC 和 125 VDC，输入功率要求为 440 瓦（典型值）和最大 500 瓦。该电源模块用于交流输入电源时，功率因数为 0.99。

IC698PSA350 是一个单插槽电源模块，安装在 RX7i 机架或插槽 0 的最左侧插槽中。它提供了各种 LED 状态指示灯，有助于识别模块的运行状态。这些指示灯包括现场正常、输出正常和温度过高 LED。该电源模块内置过热和过压保护电路以及气流保护。系统机箱下方有一个 70 CFM 强制风冷风扇，用于为电源模块提供冷却空气。如果检测到气流停止，OVER TEM LED 指示灯将启动。

IC698PSA350电源有 A 系列和 B 系列版本。A 系列电源内部安装了 0.25“ x 1.25” 保险丝，而 B 系列电源有 5 x 20 m 保险丝。安装的保险丝是 8A/250V 保险丝。

IC698PSA350电源模块是 RX7i 系列的一部分，由 GE Fanuc 制造。该模块能够通过背板向模块发送逻辑电平信号。它的额定输出功率为 350 瓦。额定工作电压为 120/240 伏交流电和 125 伏直流电。电源模块的运行频率在 47 到 63 赫兹之间。该模块的工作温度范围在 0 到 60 摄氏度之间。电源模块配有气流传感器，可以轻松检测风扇故障或驱动器周围的气流停止。如果发生任何一种情况，温度过高的 LED 会亮起。可以通过使用模块外部的跳线来启用或禁用传感器。

在安装过程中，GE Fanuc IC698PSA350电源模块不应有任何带电的电源连接，应正确接地。对于现场接线，输入端子位于模块的正面，可以连接 120/240 伏交流和 125 伏直流输入电压tage 源。端子可以用实心线或绞合线连接。接地端子或 GND 应使用 12 AWG 电线连接到机架的 GND 端子。正常操作时，安装区域的环境温度不应超过 60 摄氏度。所有输出的隔离额定值为 1500 伏直流电。IC698PSA350模块提供 15 毫秒的穿越时间，保持时间为 5 毫秒。

问题：什么是IC698PSA350？答：IC698PSA350是GE Fanuc RX120i系列的多用途、240/125 VAC或100 VDC、7 W电源。

问：IC698PSA350在什么输入电压源范围内工作？答：此电源的输入电压范围为 85 至 264 VAC 或 100 VDC 至 150 VDC。

问： 此电源有哪 3 个输出？ 答：

+5 VDC @ 60 安培

+12 VDC @ 12 安培

-12 VDC @ 4 安培

问题：IC698PSA350还能提供什么？ 答： 该模块为 RX7i 背板上的模块提供逻辑电平排序信号。

问：IC698PSA350提供什么类型的保护？ 答： 该电源输出可以跨越多达一个交流输入周期的损耗，而不会损失输出功率。该器件针对过流、过热和过压故障情况提供保护。

问：IC698PSA350有什么独特之处？ 答： 该模块提供高达 350W 的总输出功率，但需要强制风冷，由安装在机架底部的风扇托盘提供。

问：3 个 LED 表示什么？ 答：

FIELD OK（绿色）。当此 LED 亮起时，表示正在其规格范围内供电。

输出正常（绿色）。当此 LED 亮起时，表示所有 3 个 DC 通道都在其规格范围内运行。如果 3 个直流输出通道中的任何一个出现故障，则关闭。

OVER TEMP（红色）。当此 LED 亮起时，表示超过临界供气温度，或者气流传感器检测到气流停止。

问：如果我的IC698PSA350不能正常工作，我该怎么办？ 答： 您的IC698PSA350可能需要维修。

有关 GE Fanuc RX698i 系列的 IC350PSA120 多用途、240/125 VAC 或 350 VDC、7 瓦电源的更多信息，请参阅数据表用户手册。

IC698PSA350 GE  直流电源模块 连接到 RX5i 背板的设备

【英文介绍】

Technical specification

Rated voltage: 120/240 VAC or 125 VDC

Input voltage range: 85 to 264 VAC or 100 to 150 VDC

Input power: 437 watts

Output voltage: + 5 VDC, + 12VDC or -12VDC

Module type: Power supply

Rack position: Slot 0 (leftmost slot)

The GE Fanuc IC698PSA350 power module is a DC power module designed for GE enhanced RX7i PACSystems series control systems. The power module provides +12 V DC, +12 V DC, and -7 V DC power and logic level signals for devices and I/ OS connected to the RX5i backplane. Like every RX698i series module, the IC350PSA7 power module has a modular design that slides perfectly into slot 7 of the RX0i system frame. The IC698PSA350 power module is designed to maintain output power through power losses of up to 1 AC input line cycle and has built-in overcurrent, overvoltage, and electronic short circuit protection. The IC698PSA350 power module supports AC and DC inputs and has power factor correction for AC operation.

The IC698PSA350 power supply module is rated for either 120/240 volts AC or 125 volts DC, with an acceptable input range of 85 to 264 volts AC (47 to 63 Hz) or 100 to 150 volts DC. It has a rated output power of 60 watts at 350 degrees Celsius and a maximum output value of up to 500 watts. The IC698PSA350 power module has a maximum surge rating of 30 amps (115 volts AC (cold start) and 100 milliseconds at 60 amps (230 volts AC). The IC698PSA350 power module has a power factor value of 0.99 and is only effective at 90 to 260 volts AC and the isolation rating between inputs and all outputs up to 1500 volts AC for 1 minute. It has an overvoltage output limit of 7.6 to 7.66 V DC at +5 V DC output and an overcurrent limit of 5 A.

The IC698PSA350 is a high capacity power module in the PACSystem RX7i controller family. The module is used to provide the backplane power supply, which the module uses to activate the internal circuitry and make it operational. This power module occupies a single slot in the chassis and is designed to be installed only in slot 7 of the RX0i rack.

The IC698PSA350 operates at an input supply voltage of 85 to 264 VAC and at an AC input frequency of 100-150 Hz at a voltage of 47 to 63VDC. The module is rated at 120/240 VAC and 125 VDC, with input power requirements of 440 watts (typical) and a maximum of 500 Watts. The power factor of the power module is 0.99 when it is used for AC input power.

The IC698PSA350 is a single-slot power module that is installed in the leftmost slot of the RX7i rack or slot 0. It provides a variety of LED status indicators that help identify the operating status of the module. These indicators include field normal, output normal, and overtemperature leds. The power module has built-in overheat and overvoltage protection circuits and airflow protection. There is a 70 CFM forced air cooling fan under the system chassis to provide cooling air to the power module. If a stop in airflow is detected, the OVER TEM LED indicator will activate.

The IC698PSA350 power supply is available in A Series and B Series versions. The A Series power supply has a 0.25 "x 1.25" fuse installed inside, while the B Series power supply has a 5 x 20 m fuse. The fuse installed is an 8A/250V fuse.

The IC698PSA350 power module is part of the RX7i family and is manufactured by GE Fanuc. The module can send logic level signals to the module through the backplane. It has a rated output of 350 watts. The rated operating voltage is 120/240 volts AC and 125 volts DC. The power module operates at a frequency between 47 and 63 Hertz. The module operates in a temperature range between 0 and 60 degrees Celsius. The power module is equipped with an air flow sensor that can easily detect fan failure or air flow stoppage around the drive. If either happens, the overheated LED will light up. Sensors can be enabled or disabled by using jumpers outside the module.

During the installation, the GE Fanuc IC698PSA350 power module should not have any live power connection and should be properly grounded. For field wiring, the input terminals are located on the front of the module and can be connected to 120/240 V AC and 125 V DC input voltage tage sources. Terminals can be connected with solid or twisted wires. The ground terminal or GND should be connected to the GND terminal of the rack using 12 AWG wires. During normal operation, the ambient temperature in the installation area should not exceed 60 degrees Celsius. The isolation rating for all outputs is 1500 volts DC. The IC698PSA350 module provides a traverse time of 15 milliseconds and a hold time of 5 milliseconds.

Question: What is IC698PSA350? A: The IC698PSA350 is a versatile, 240/125 VAC or 100 VDC, 7 W power supply for the GE Fanuc RX120i series.

Q: In what range of input voltage sources does the IC698PSA350 operate? A: The input voltage range of this power supply is 85 to 264 VAC or 100 VDC to 150 VDC.

Q: What are the 3 outputs of this power supply? A:

+5 VDC @ 60 amps

+12 VDC @ 12 amps

-12 VDC @ 4 amps

Q: What else does the IC698PSA350 offer? A: This module provides a logic level ordering signal for the module on the RX7i backplane.

Q: What type of protection does the IC698PSA350 provide? A: The power supply output can span losses of up to one AC input cycle without loss of output power. The device provides protection against overcurrent, overheat and overvoltage failures.

Q: What is unique about the IC698PSA350? A: The module provides a total output power of up to 350W, but requires forced air cooling, provided by a fan tray mounted on the bottom of the rack.

Q: What do three leds mean? A:

FIELD OK (green). When this LED lights up, it means that power is being supplied within its specifications.

The output is normal (green). When this LED lights up, it means that all 3 DC channels are operating within their specifications. If any of the three DC output channels fails, they are closed.

OVER TEMP (red). When this LED lights up, it indicates that the critical gas supply temperature has been exceeded, or the gas flow sensor has detected a stop in the flow.

Q: What should I do if my IC698PSA350 does not work properly? A: Your IC698PSA350 may need repair.

For more information about the GE Fanuc RX698i series IC350PSA120 multipurpose, 240/125 VAC or 350 VDC, 7 watt power supply, please refer to the Datasheet User manual.

【其他型号推荐】