GE IC755ACC07GAS 安装操作员界面端子 设备兼容

【产品详情】

 GE Fanuc IC755ACC07GAS 替换垫片是一种可以安装操作员界面端子的结构。它与 7 英寸 Quickanel+ 设备兼容。

IC755ACC07GAS垫片是 Quickpanel+ 系列设备的替代垫片。该附件已包含在 GE Fanuc 智能平台部门的 Quickpanel+ 系列操作界面中。该特定附件旨在取代操作员界面模块的原始垫圈。原来的垫圈预装在模块中，由于持续磨损，可能需要更换。用于 Quickpanel+ 设备的 GE Fanuc IC755ACC07GAS 更换垫圈在设备的顶部和底部带有 4 个安装孔，可用于将模块固定到表面上。为避免垫圈退化，需要限制装置的插入或拆卸，并且需要偶尔重新拧紧安装夹。

在为 Quickpanel+ 设备安装 GE Fanuc IC755ACC07GAS 替换垫圈时，重要的是要知道该设备需要在没有任何电缆的情况下插入，否则它将不适合垫圈。还需要先拆下电源。断开设备的电源后，用户需要验证 Quickpanel+ 设备的 GE Fanuc IC755ACC07GAS 更换垫圈是否位于设备侧面的边框通道中。然后需要固定垫圈，要正确固定，需要 0.3 N-m 的扭矩范围。Quickpanel+ 系列中的所有装置都可以在 0 至 50 摄氏度的温度范围内运行，最大相对湿度为 85%，而不会结露。

GE IC755ACC07GAS 安装操作员界面端子 设备兼容

【英文介绍】

The GE Fanuc IC755ACC07GAS replacement gasket is a structure for mounting operator interface terminals. It is compatible with 7-inch Quickanel+ devices.

The IC755ACC07GAS gasket is an alternative gasket for the Quickpanel+ series of devices. The attachment is included in the Quickpanel+ series operating interface of GE Fanuc's Intelligent Platforms division. This particular attachment is intended to replace the original gasket of the operator interface module. The original gasket was pre-installed in the module and may need to be replaced due to continuous wear. The GE Fanuc IC755ACC07GAS replacement gasket for Quickpanel+ devices comes with 4 mounting holes on the top and bottom of the device that can be used to secure the module to the surface. To avoid gasket degradation, the insertion or removal of the device needs to be limited, and the mounting clamp needs to be re-tightened occasionally.

When installing a GE Fanuc IC755ACC07GAS replacement gasket for a Quickpanel+ device, it is important to know that the device needs to be plugged in without any cable, otherwise it will not fit the gasket. We need to remove the power first. After disconnecting the device, the user needs to verify that the Quickpanel+ device's GE Fanuc IC755ACC07GAS replacement gasket is located in the bezel channel on the side of the device. The gasket then needs to be fixed, and to be fixed correctly, a torque range of 0.3N-m is required. All units in the Quickpanel+ series can operate in a temperature range of 0 to 50 degrees Celsius with a maximum relative humidity of 85% without condensation.

GE IC755ACC07GAS 安装操作员界面端子 设备兼容

【其他型号推荐】