GE IC697PWR722 电源模块 电路过流保护

【产品详情】

技术规格

额定电压： 24 伏直流电

输入电压范围： 21 至 32 VDC

输入功率： 满载时 156 瓦

输出功率 90 瓦

底板上的位置： 最左边的插槽或作为独立单元

直流输出： +5VDC、+12 VDC、-12 VDC

IC697PWR722模块是一种电源模块，经过设计和制造，可与 90-70 系列的可编程控制器一起使用。该模块可在 21 至 32 伏直流电压的电压下运行，包括 3 个调节电压，总输出功率达到 90 瓦。这些额定电压为 5、12 和 -12 伏直流电，工作电流分别为 16.5、1.5 和 1 安培。GE Fanuc Automation IC697PWR722电源模块位于机架的左侧，可以连接或安装在机架上。为了正常运行，该模块需要连接到兼容的电源适配器模块，例如将电源输出连接到机架背板的 IC697PWR720 模块。该模块还有助于监控电源模块的TTL信号。该模块还将定义此模块的操作逻辑。

GE Fanuc Automation IC697PWR722电源模块包括其所有输出和输入以及系统复位信号的电路过流保护。该电源模块可实现双机架操作。当第二个机架连接到此模块时，该机架只需要 5 伏的电源，并且第二个机架消耗的电流必须小于 5.2 安培。第二个机架必须位于第一个机架附近。连接电缆的最大长度为 3 英尺。GE Fanuc Automation IC697PWR722电源模块可以通过 2 种不同的方式安装，右侧面板在工厂安装并安装在面板上，或者使用面板连接到机架的左侧，第二种选择包括从电源上拆下右侧面板，并且需要使用额外的硬件。

GE IC697PWR722 电源模块 电路过流保护

【英文介绍】

Technical specification

Rated voltage: 24 volts DC

Input voltage range: 21 to 32 VDC

Input power: 156W at full load

The output power is 90 watts

Position on the bottom plate: the leftmost slot or as a stand-alone unit

Dc output: +5VDC, +12 VDC, -12 VDC

The IC697PWR722 module is a power supply module that has been designed and manufactured to work with the 90-70 series of programmable controllers. The module can operate at voltages ranging from 21 to 32 volts DC, including 3 regulating voltages, for a total output power of 90 watts. These are rated at 5, 12 and -12 volts DC and operate at 16.5, 1.5 and 1 amp, respectively. The GE Fanuc Automation IC697PWR722 power module is located on the left side of the rack and can be attached or mounted on the rack. In order to function properly, the module needs to be connected to a compatible power adapter module, such as the IC697PWR720 module that connects the power output to the backplane of the rack. The module also helps monitor the TTL signal of the power module. The module will also define the operation logic for this module.

The GE Fanuc Automation IC697PWR722 power module includes current protection for all its outputs and inputs as well as system reset signals. The power module supports two-rack operation. When a second rack is connected to this module, the rack requires only 5 volts of power, and the current consumed by the second rack must be less than 5.2 amps. The second rack must be located near the first rack. The maximum length of the connecting cable is 3 feet. The GE Fanuc Automation IC697PWR722 power supply module can be installed in 2 different ways, the right panel is factory installed and mounted on the panel, or connected to the left side of the rack using the panel, the second option involves removing the right panel from the power supply and requires the use of additional hardware.

GE IC697PWR722 电源模块 电路过流保护

【其他型号推荐】