IC697MDL752 输出模块是GE Fanuc组件 具有保护功能

【产品详情】

IC697MDL752输出模块是GE Fanuc组件，设计用于安装到GE 90-70系列PLC的机架中。该模块为各种机器系统和应用提供了配置和定制的可能性，并在直流电源上运行。这款高品质 PLC 附件可作为正逻辑分立式输出模块运行，提供多达 32 个输出点。与该系列的其他类似组件一样，该输出模块还具有通用功能，例如特殊的键控系统和有组织的布线。该模块旨在与可编程控制器一起使用，可编程控制器是在恶劣工业条件下运行的大型复杂机器系统的基本硬件。

技术规格

额定电压： 12 伏直流电

输出数量： 32 个输出（4 组，每组 8 个）

输出电流： 每点 0.5 安培，每组 2 安培

所需电流： 0.25 安培

输出电压范围： 10 至 15 伏

直流电源： 是的

IC697MDL752输出模块在打开和关闭时只需 1 毫秒即可响应。高度可靠的输出模块具有所有必要的保护功能，并符合总线标准（如VME标准）的要求。该模块遵循标准 C.1 修订版中的规定，需要 0.25 安培的电流。IC697MDL752模块具有 12 伏直流电压额定值，其输出分为 4 组，每组 8 组。该模块的输出电压范围为 10 至 15 伏，浪涌电流为 10 安培。只需几个简单的步骤即可安装IC697MDL752模块。此外，通过按下位于外壳盖背面的塑料夹，可以很容易地从机架上卸下模块。此外，该模块还具有方便的接线端子板，允许安装规格为 AWG #22 或 #14 的电线。

IC697MDL752 输出模块是GE Fanuc组件 具有保护功能

【英文介绍】

The IC697MDL752 output module is a GE Fanuc component designed to be installed into the rack of the GE 90-70 series PLC. The module offers the possibility of configuration and customization for a variety of machine systems and applications, and runs on a DC power supply. This high-quality PLC accessory operates as a positive logic discrete output module with up to 32 output points. Like other similar components in the series, this output module also has general-purpose features such as a special keying system and organized wiring. The module is designed to be used with programmable controllers, which are the basic hardware for large complex machine systems operating in harsh industrial conditions.

Technical specification

Rated voltage: 12 volts DC

Number of outputs: 32 outputs (4 sets of 8 each)

Output current: 0.5 amps per point, 2 amps per group

Required current: 0.25 amps

Output voltage range: 10 to 15 volts

Dc power supply: Yes

The IC697MDL752 output module responds in just 1 millisecond when turned on and off. The highly reliable output module has all the necessary protection features and meets the requirements of bus standards such as the VME standard. The module complies with the requirements of standard C.1 revision and requires a current of 0.25 amps. The IC697MDL752 module has a 12-volt DC voltage rating and its output is divided into 4 groups of 8 each. The module has an output voltage range of 10 to 15 volts and an inrush current of 10 amps. Install the IC697MDL752 module in just a few simple steps. In addition, the module can be easily removed from the rack by pressing the plastic clip located on the back of the housing cover. In addition, the module has a convenient terminal board that allows the installation of wires with AWG #22 or #14 specifications.

IC697MDL752 输出模块是GE Fanuc组件 具有保护功能

【其他型号推荐】