GE Fanuc IC697MDL350 分立式输出模块 采用机械键控

【产品详情】

技术规格

额定电压： 120 伏交流电

输出数量： 32 个输出（4 组，每组 8 个）

输出电流： 每点 0.5 安培，每组 2 安培

所需电流： 0.5 安培

频率： 47 至 63 赫兹

直流电源： 不

 IC697MDL350模块是GE Fanuc制造的分立式输出模块，是90-70系列的一部分。它的工作电压为 120 伏交流电，0 个输出点中的每一个都具有 5.32 安培的电流容量，这些输出点被隔离成 4 组，每组 8 个点。该模块具有约20倍额定电流的高浪涌容量。它允许在不同的交流电源相位上使用每 8 个点组。每个输出组都与额定电流为 5 安培的保险丝熔断，并显示浪涌电流，使输出适用于各种感性负载。IC697MDL350输出模块具有 LED 指示灯，用于指示电路 PLC 侧每个输出点的开/关状态。它还具有一个 LED，可显示模块顶部保险丝的状态。

GE Fanuc IC697MDL350输出模块采用机械键控，通过使用相同类型的模块进行更换来增强更换过程。该模块的用户无需跳线或DIP开关即可执行I/O参考的配置功能。配置是通过 MS-DOS 或 Windows 编程软件完成的，这些软件通过 SNP 端口或以太网 TCP/IP 端口在 Windows 95 或 Windows NT 操作系统上运行。此配置功能预装在用于编程的设备上。IC697MDL350输出模块与许多负载设备（如指示灯、螺线管和电机起动器）完美匹配。0.5 安培电流额定值适用于每个点的长期电流值。由于模块具有散热功能，因此在高温下，每个输出组的总电流都会受到限制。

GE Fanuc IC697MDL350 分立式输出模块 采用机械键控

【英文介绍】

Technical specification

Rated voltage: 120 volts AC

Number of outputs: 32 outputs (4 sets of 8 each)

Output current: 0.5 amps per point, 2 amps per group

Required current: 0.5 amp

Frequency: 47 to 63 Hz

Dc power supply: No

The IC697MDL350 module is a discrete output module manufactured by GE Fanuc as part of the 90-70 series. It operates at 120 volts AC and has a current capacity of 5.32 amps at each of its 0 output points, which are isolated into 4 groups of 8 points each. The module has a high surge capacity of about 20 times the rated current. It allows each group of 8 points to be used on different AC power supply phases. Each output group is fused with a 5 amp rated fuse and displays the inrush current, making the output suitable for a variety of inductive loads. The IC697MDL350 output module has an LED indicator to indicate the on/off status of each output point on the PLC side of the circuit. It also has an LED that shows the status of the fuse at the top of the module.

The GE Fanuc IC697MDL350 output module is mechanically keyed to enhance the replacement process by using the same type of module for replacement. Users of the module can perform configuration functions for I/O reference without a jumper or DIP switch. Configuration is done via MS-DOS or Windows programming software that runs on Windows 95 or Windows NT operating systems via SNP ports or Ethernet TCP/IP ports. This configuration feature comes pre-installed on the device used for programming. The IC697MDL350 output module is a perfect match for many load devices such as indicator lights, solenos and motor starters. The 0.5 amp current rating is a long-term current value for each point. Because the module has a heat dissipation function, the total current of each output group is limited at high temperatures.

GE Fanuc IC697MDL350 分立式输出模块 采用机械键控

【其他型号推荐】