GE Fanuc IC697MDL251 输入模块 经过机械调整

【产品详情】

技术规格

额定电压： 120 伏交流电

输入数量： 16 个输入（4 个隔离组，每组 4 个）

输入电流： 10毫安

所需电流： 0.35 安培

频率： 60赫兹

直流电源： 不

GE Fanuc IC697MDL251模块是 GE Fanuc 制造的输入模块，是 90-70 系列产品线的一部分。IC697MDL251 输入模块带有 16 个输入点，分为 4 个单独的组，每个组有 4 个点。这些组中的每一个都与不同的交流电压供应相兼容，并且可以与不同的交流电压供应相一起使用，因为每个组都是隔离的。IC697MDL251模块经过机械调整，可在现场轻松更换类似类型的模块。这款 16 点输入模块与各种输入设备完美匹配，包括限位和选择开关、按钮以及电子 2 线和 3 线接近开关。通过设备背板上的 0 伏总线需要 35.5 安培的电流。

GE Fanuc IC697MDL251输入模块有一个机械钥匙，专门用于防止特定插槽中模块的任何意外或未经授权的切换。当用户想要在钥匙锁定过程后更改模块的位置时，模块允许在钥匙向上推时将其移除，因此在钥匙脱离导轨时会松开。确定安装位置后，可以重新插入模块和钥匙。IC697MDL251模块的接线需要从电源连接到所有 4 个输入组的输入端子。线径 14 至线径 22 可用于可拆卸现场接线端子板。电线束通过电缆扎带在端子板上受到保护，电缆扎带穿过板下角的夹板。卸下电路板时必须关闭主电源。

GE Fanuc IC697MDL251 输入模块 经过机械调整

【英文介绍】

Technical specification

Rated voltage: 120 volts AC

Number of inputs: 16 inputs (4 isolation groups, 4 per group)

Input current: 10 MA

Required current: 0.35 amps

Frequency: 60 Hz

Dc power supply: No

The GE Fanuc IC697MDL251 module is an input module manufactured by GE Fanuc as part of the 90-70 series product line. The IC697MDL251 input module comes with 16 input points divided into 4 separate groups with 4 points each. Each of these groups is compatible with a different AC voltage supply and can be used with a different AC voltage supply because each group is isolated. The IC697MDL251 module is mechanically adjusted to allow easy replacement of similar modules in the field. The 16-point input module perfectly matches a wide range of input devices, including limit and select switches, buttons, and electronic 2-wire and 3-wire proximity switches. It takes 35.5 amps of current to pass through the 0 volt bus on the backplane of the device.

The GE Fanuc IC697MDL251 input module has a mechanical key specifically designed to prevent any accidental or unauthorized switching of the module in a particular slot. When the user wants to change the position of the module after the key locking process, the module allows it to be removed when the key is pushed up, so it will release when the key comes off the rail. After determining the installation location, you can reinsert the module and key. The wiring of the IC697MDL251 module needs to be connected from the power supply to the input terminals of all 4 input groups. Wire diameters 14 to 22 are available for removable field terminal boards. The cable harness is protected on the terminal board by cable ties. The cable ties pass through the cleats at the lower corners of the board. The main power supply must be turned off when removing the circuit board.

GE Fanuc IC697MDL251 输入模块 经过机械调整

【其他型号推荐】