IC697CPX928 CPU模块中央处理器 通信端口

【产品详情】

技术规格

模块类型： 中央处理器

插槽数量： 1 （单插槽）

所需电流： 3.1 安培

点数： 12K 输入和输出（任意混音）

串口： 三个（RS-232 和 RS-485）

支持： IC660/IC661 I/O 和 IC697 I/O

GE Fanuc IC697CPX928模块是基于80486DX4微处理器的CPU模块。它由 GE Fanuc Automation 制造，是 90-70 系列产品线的成员，时钟频率为 96 兆赫兹。本机还支持浮点数据以及 32 位指令。CPU模块配备容量为6 MB的中速RAM，由一体式锂电池备份。该电池是可更换的，可更换电池是IC697ACC701电池。电池能够将存储在 RAM 中的数据保留最多 6 个月。它的标称电流为 3.1 安培，额定输入电压为 5 伏直流电。该模块的强制风冷额定值为 70 CFM，工作环境温度范围为 32 至 140 华氏度。GE Fanuc IC697CPX928 CPU 模块在没有风冷的情况下，可在 32 至 122 华氏度的温度范围内运行。

根据可用的电源，可以安装在 GE Fanuc IC697CPX928 CPU 模块上的机架风扇组件包括 240 伏交流电、120 伏交流电或 24 伏直流额定机架风扇组件。该 CPU 模块具有 3 个串行端口，即 2 个 RS-485 通信端口和 1 个 RS-232 通信端口。串行端口用于与编程设备连接以配置 CPU。此外，还有一个可选的以太网模块，也可以安装在PLC上，通过使用以太网网络增强GE IC697CPX928 CPU模块的配置。本机共有 7 个 LED 指示灯，放置在模块前面，用于启用各种状态更新。

该控制器专门配备了七 （7） 个状态 LED、用于保留随机存取存储器 （RAM） 内容的锂电池以及通信端口，例如一 （1） 个 RS232 串行端口、两 （2） 个 RS485 串行端口和一 （1） 个恢复出厂设置端口。

该IC697CPX928与各种选件模块兼容，以增强 CPU 并为其提供附加功能。这些选件模块包括以太网接口模块、可编程协处理器、字母数字协处理器、总线控制器、通信模块、I/O 链路接口以及整个 IC697 分立和模拟 I/O 模块系列。

IC697CPX928模块所需的标称电流为 3.1 安培。所需的输入电压为 5 伏直流电。该模块采用额定值为 70 CFM 的强制风冷，可在 32 至 140 华氏度的环境温度下运行。

IC697CPX928 CPU模块中央处理器 通信端口

【英文介绍】

Technical specification

Module type: CPU

Number of slots: 1 (single slot)

Required current: 3.1 amps

Points: 12K input and output (any mix)

Serial ports: three (RS-232 and RS-485)

Support: IC660/IC661 I/O and IC697 I/O

The GE Fanuc IC697CPX928 module is a CPU module based on the 80486DX4 microprocessor. It is manufactured by GE Fanuc Automation and is a member of the 90-70 series product line with a clock frequency of 96 MHZ. The native also supports floating point data as well as 32-bit instructions. The CPU module is equipped with medium-speed RAM with a capacity of 6 MB, backed up by an integrated lithium battery. The battery is replaceable and the replaceable battery is the IC697ACC701 battery. The battery is capable of retaining data stored in RAM for up to 6 months. It has a nominal current of 3.1 amps and a rated input voltage of 5 volts DC. The module has a forced air cooling rating of 70 CFM and an operating ambient temperature range of 32 to 140 degrees Fahrenheit. The GE Fanuc IC697CPX928 CPU module can operate in a temperature range of 32 to 122 degrees Fahrenheit without air cooling.

Depending on the available power supply, rack fan assemblies that can be installed on the GE Fanuc IC697CPX928 CPU module include rack fan assemblies rated at 240 volts AC, 120 volts AC, or 24 volts DC. The CPU module has three serial ports, namely two RS-485 communication ports and one RS-232 communication port. Serial ports are used to connect to programming devices to configure the CPU. In addition, there is an optional Ethernet module that can also be installed on the PLC to enhance the configuration of the GE IC697CPX928 CPU module by using Ethernet networking. The unit has a total of 7 LED indicators, placed in front of the module, to enable various status updates.

The controller is specially equipped with seven (7) status leds, a lithium battery for retaining the contents of random access memory (RAM), and communication ports such as one (1) RS232 serial port, two (2) RS485 serial ports, and one (1) factory reset port.

The IC697CPX928 is compatible with various option modules to enhance the CPU and provide it with additional functionality. These option modules include Ethernet interface modules, programmable coprocessors, alphanumeric coprocessors, bus controllers, communication modules, I/O link interfaces, and the entire IC697 family of discrete and analog I/O modules.

The nominal current required for the IC697CPX928 module is 3.1 amps. The required input voltage is 5 volts DC. The module uses forced air cooling rated at 70 CFM and can operate at ambient temperatures ranging from 32 to 140 degrees Fahrenheit.

IC697CPX928 CPU模块中央处理器 通信端口

【其他型号推荐】