IC697BEM763 高性能接口模块 带有一个单插槽模块

【产品详情】

IC697BEM763模块是GE Fanuc制造的接口模块。它是一种工业自动化设备，与 GE 90-70 系列 PLC 和 VME 机架一起使用。它是一种可编程控制器设备，带有一个单插槽模块，可在局域网和 PLC 系统之间提供增强的接口。该模块允许 PLC 应用程序对 DC300、AC2000 和 DC2000 驱动器进行配置和控制。该接口模块配备 80C186 微处理器，时钟速度为 12 Mhz。IC697BEM763模块使用 3 个状态 LED 来处理不同的事件。“Module OK LED”显示接口模块的当前运行状态。此 LED 指示灯在诊断过程中闪烁。其他 LED 是“命令输出 LED”和“数据输入 LED”。“Command Out LED”在自检过程中亮起，并在 PLC 的命令发送到网络丢弃时闪烁。当从网络丢弃接收到数据消息时，“Data In LED”闪烁。

GE Fanuc 90-70 系列IC697BEM763模块完全符合 FCC 和 VME 标准。该模块的工作温度范围为 0 至 60 摄氏度，环境相对湿度为 5% 至 95%。IC697BEM763模块带有一个重启按钮，该按钮将停止DLAN通信并对模块进行内部测试。模块中的 8 针 DLAN 网络连接器提供从 DLAN 模块到网络的连接。IC697BEM763模块同时支持DLAN和DLAN+网络协议。DLAN协议是一种多点串行协议，而DLAN+协议是一种基于ARCnet网络的高速协议。

IC697BEM763是GE Fanuc设计的90-70系列高性能接口模块。 该部件提供 90-70 系列 PLC 系统和 GE Drive Systems DLAN / DLAN+ LAN 协议之间的自动化。IC697BEM763模块允许通过 2000-300 系列程序控制 AC2000、DC90 和 DC70 等驱动器。GE Drive系统仅使用DLAN或DLAN+局域网协议进行通信。

IC697BEM763模块可作为DLAN或DLAN+控制器运行。需要注意的是，单个模块不能同时是DLAN和DLAN+控制器。在应用同时需要DLAN和DLAN+设备的情况下，必须使用两个DLAN接口模块。在单机架系统中，IC697BEM763模块与 PLC 处理器位于同一机架中。在多机架系统中，IC697BEM763模块可以位于中央处理器机架或扩展机架中。

在安装过程中，CPU 电源单元和 IC697BEM763 模块必须位于每个机架内的指定插槽中。CPU 模块必须位于机架 1 的插槽 0 中。当 IC697BEM763 模块系统包含 BTM 时，只要它不在空插槽的右侧，就可以将其分配到任何插槽中。如果 PLC 系统有多个机架，则IC697BEM763模块必须位于每个扩展插槽的插槽 1 中。请注意： IC697BEM763A必须安装在所有其他 GE Fanuc 模块的右侧。IC697BEM763A和 CPU 模块之间不能有空插槽。

IC697BEM763 高性能接口模块 带有一个单插槽模块

【英文介绍】

The IC697BEM763 module is an interface module manufactured by GE Fanuc. It is an industrial automation device used with GE 90-70 series PLC and VME racks. It is a programmable controller device with a single slot module that provides an enhanced interface between a LAN and a PLC system. This module allows PLC applications to configure and control DC300, AC2000, and DC2000 drives. The interface module is equipped with an 80C186 microprocessor with a clock speed of 12 Mhz. The IC697BEM763 module uses 3 status leds to handle different events. Module OK LED Displays the current operating status of the interface module. This LED indicator blinks during diagnosis. Other leds are "Command output LED" and "data input LED". The "Command Out LED" lights up during the self-test and blinks when the PLC's command is sent to the network for discard. When a Data message is received from the network, the "Data In LED" blinks.

GE Fanuc 90-70 Series IC697BEM763 modules are fully compliant with FCC and VME standards. The module operates in a temperature range of 0 to 60 degrees Celsius and an ambient relative humidity of 5 to 95 percent. The IC697BEM763 module comes with a restart button that will stop DLAN communication and conduct internal tests on the module. The 8-pin DLAN network connector in the module provides connectivity from the DLAN module to the network. The IC697BEM763 module supports both DLAN and DLAN+ network protocols. DLAN protocol is a multipoint serial protocol, while DLAN+ protocol is a high-speed protocol based on ARCnet network.

The IC697BEM763 is a series of 90-70 high-performance interface modules designed by GE Fanuc. This part provides automation between the 90-70 series PLC Systems and GE Drive Systems DLAN/DLAN+ LAN protocols. The IC697BEM763 module allows control of drives such as AC2000, DC90 and DC70 through 2000-300 series programs. The GE Drive system uses only the DLAN or DLAN+ LAN protocol for communication.

The IC697BEM763 module can operate as a DLAN or DLAN+ controller. It is important to note that a single module cannot be both a DLAN and a DLAN+ controller. When applications require both DLAN and DLAN+ devices, two DLAN interface modules must be used. In a stand-alone system, the IC697BEM763 module is located in the same rack as the PLC processor. In a multi-rack system, the IC697BEM763 module can be located in a central processor rack or an extension rack.

During installation, the CPU power supply unit and the IC697BEM763 module must be located in a designated slot within each rack. The CPU module must be located in slot 0 of rack 1. When the IC697BEM763 module system contains a BTM, it can be assigned to any slot as long as it is not to the right of the empty slot. If the PLC system has multiple racks, the IC697BEM763 module must be located in slot 1 of each expansion slot. Please note: The IC697BEM763A must be installed to the right of all other GE Fanuc modules. There is no vacant slot between the IC697BEM763A and the CPU module.

IC697BEM763 高性能接口模块 带有一个单插槽模块

【其他型号推荐】