GE IC697BEM734 单通道 I/O 总线控制器 串行总线地址

【产品详情】

GE Fanuc IC697BEM734 90-70 系列单通道 I/O 总线控制器，用于 90 系列、70 系列和 90-70 系列总线系统。该总线控制器安装在 90-70 系列 PLC 机架的单个插槽中。与所有697-734系列总线控制器一样，IC697BEM734总线控制器可以使用基于MS-DOS的配置软件配置器功能进行配置，提供直观的编程环境，并允许操作员指定和设置波特率和串行总线地址。默认情况下，IC153BEM6总线控制器设置为31.<> kbaud作为标准波特率，默认串行总线地址设置为<>，但用户可以通过配置软件选择特定的波特率和串行总线地址。

IC697BEM734总线控制器允许称为数据报的数据消息在设备之间传输，或通过梯形图逻辑命令广播到总线上所有连接的设备。当与系列一或系列六PLC系统一起使用时，它可以异步扫描I/O块，并在每次迭代背板扫描后自动将I/O数据传输到CPU。每次完成扫描后，IC697BEM734总线控制器都会接收任何故障数据，在每次完成扫描时指定 CPU 的诊断参考，并将 CPU 启动的梯形图逻辑命令传输到总线上的所有设备。IC697BEM734总线控制器支持IC666总线上的全局通信、直接PLC CPU通信服务请求和点对点数据传输。IC697BEM734总线控制器的额定直流电压为 5 伏，最大背板电流为 1.3 安培。它具有 3 个前端 LED，用于指示总线控制器操作和总线通信状态。

GE 发那科IC697BEM734 IC660/IC661总线控制器是用于GE IC66总线系统的单通道I/O总线控制器。IC697BEM734总线控制器仅占用GE IC66 PLC机架上的一个插槽，并配置了基于Windows（MS-DOS）的编程软件。IC697BEM734总线控制器异步扫描IC66（IC660或IC661）I/O块，在IC697 PLC背板每次迭代扫描后将I/O数据传输到PLC CPU。在扫描过程中，IC697BEM734总线控制器在每次完成扫描时接受来自 PLC CPU 诊断参考的任何故障信息，并将梯形图逻辑命令从 CPU 传输到连接的现场设备。该模块支持的通信选项包括全局通信、由 PLC CPU 通信服务请求发起的定向通信和点对点 IC666 总线数据传输（它充当其他设备的通信节点）。

IC697BEM734总线控制器是使用基于 MS-DOS 的编程软件配置器功能配置的。作为标准过程，基于 MS-DOS 的编程软件配置器功能将默认波特率设置为 153.6K 波特，将默认串行总线地址设置为 31，但操作员可以使用基于 MS-DOS 的编程软件指定波特率和串行总线地址。数据消息，通常称为“数据报”，可以从一个设备传输到另一个设备，或者通过梯形图逻辑命令广播到网络上的所有设备。IC697BEM734总线控制器的额定电压为 5 伏直流电，背板电流为 1.3 安培。IC697BEM734总线控制器具有 3 个 LED 指示灯，用于显示操作和通信状态，并带有一个用于连接到手持监视器的后端串行端口 （PL1） 和一个用于连接到总线字段的总线现场终端连接器 （PL3）。

GE IC697BEM734 单通道 I/O 总线控制器 串行总线地址

【英文介绍】

GE Fanuc IC697BEM734 90-70 Series single-channel I/O bus controller for 90 series, 70 Series and 90-70 series bus systems. The bus controller is installed in a single slot in the 90-70 series PLC rack. Like all 697-734 series bus controllers, the IC697BEM734 bus controller can be configured using the MS-DOs-based configuration software Configurator feature, providing an intuitive programming environment and allowing operators to specify and set baud rates and serial bus addresses. By default, the IC153BEM6 bus controller is set to 31.<> kbaud as the standard baud rate and the default serial bus address is set to <>, but the user can select a specific baud rate and serial bus address through the configuration software.

The IC697BEM734 bus controller allows data messages called datagrams to be transmitted between devices or broadcast to all connected devices on the bus via ladder logic commands. When used with Series one or Series six PLC systems, it can asynchronously scan I/O blocks and automatically transfer I/O data to the CPU after each iteration of the backplane scan. After each complete scan, the IC697BEM734 bus controller receives any fault data, specifies the diagnostic reference for the CPU at each complete scan, and transmits the ladder diagram logic command for CPU startup to all devices on the bus. The IC697BEM734 bus controller supports global communication over the IC666 bus, direct PLC CPU communication service requests, and point-to-point data transfer. The IC697BEM734 bus controller has a rated DC voltage of 5 volts and a maximum backplane current of 1.3 amps. It has 3 front leds that indicate bus controller operation and bus communication status.

The GE Fanuc IC697BEM734 IC660/IC661 bus controller is a single-channel I/O bus controller for GE IC66 bus systems. The IC697BEM734 bus controller occupies only one slot in the GE IC66 PLC rack and is configured with Windows (MS-DOS) -based programming software. The IC697BEM734 bus controller asynchronously scans IC66 (IC660 or IC661) I/O blocks, transferring I/O data to the PLC CPU after each iteration of the IC697 PLC backplane scan. During the scan, the IC697BEM734 bus controller accepts any fault information from the PLC CPU diagnostic reference at each completion of the scan and transfers the ladder logic command from the CPU to the connected field device. Communication options supported by this module include global communication, directed communication initiated by PLC CPU communication service requests, and point-to-point IC666 bus data transfer (which acts as a communication node for other devices).

The IC697BEM734 bus controller is configured using the MS-DOs-based programming software Configurator function. As a standard procedure, the MS-DOs-based programming software Configurator feature sets the default baud rate to 153.6K baud and the default serial bus address to 31, but the operator can specify the baud rate and serial bus address using MS-DOs-based programming software. Data messages, often called "datagrams," can be transmitted from one device to another, or broadcast to all devices on the network via ladder logic commands. The IC697BEM734 bus controller is rated at 5 volts DC and the backplane current is 1.3 amps. The IC697BEM734 bus controller has 3 LED indicators for displaying operation and communication status and comes with a back-end serial port (PL1) for connecting to the handheld monitor and a bus field terminal connector (PL3) for connecting to the bus field.

GE IC697BEM734 单通道 I/O 总线控制器 串行总线地址

【其他型号推荐】