IC697BEM731 总线控制器模块 天才总线控制器

【产品详情】

产品描述

IC697BEM731是GE Fanuc为90-70系列制造的总线控制器模块（BCM）。 IC697BEM731专为Genius I/O手持显示器IC660/IC661而设计。 这 IC697BEM731模块可用作单通道控制器;因此它仅占用单个手持显示器（IC66*）PLC插槽。此 BCM 异步扫描 IC66* 输入/输出模块;因此，每次扫描一次，I/O 数据通过 IC697 PLC 机架的背板传输到 CPU。 IC697BEM731 BCM 还负责支持源自 PLC CPU 通信服务请求的定向通信。此外，它可以被配置成执行全局通信。 IC697BEM731只能通过MS DOS或Windows编程软件配置功能进行配置。

IC697BEM731的其他特性 包括每通道 30 个压降、IC66* 或 IC661 I/O 诊断、支持冗余块、电缆和 CPU、LAN 通信、CPU 软配置和报警处理器功能。 安装前，请参阅适用的 PLC 安装手册。启动前应关闭电源。按照说明安装机架，然后打开电源。如果操作正确，模块将通过相应的闪烁 LED 上电。当从 CPU 接收到配置并验证总线操作时，中间 LED 将发出 ON。底部的指示灯始终熄灭。

技术规格

模块类型： 天才总线控制器

有效数据速率： 不适用

不。频道数量： 1

每通道跌落数： 30

串口： 1（手持式显示器端口）

当前需要： 1.3 安培

用于建立网络的物理通信电缆是百通9182型电缆，GE目录号为IC660BLC001,15英寸，数量3，IC660BLC003,36英寸，数量1。总线终结器插头必须安装在总线的两端，目录号为 IC660BLM506 150 欧姆，数量 4 和 IC660BLM508,75 欧姆，数量 4 电阻器。

IC697BEM731总线控制器支持通过基于 Windows 的软件配置在 CPU 之间传输全局数据，并且可以通过 IC697 PLC 报警系统进行增强，以在处理器的数据表上报告带有时间戳的故障。该总线控制器模块的后端有一个手持监视器端口，用于连接手持监视器设备，以及一个用于建立IC66总线连接的连接器。IC697BEM731总线控制器配置了基于 Windows 或 MS-DOS 的配置器功能。默认情况下，基于 Windows 的配置器功能将波特率设置为 153.5 Kilo-Bauds，将串行总线地址设置为 31。其他波特率和串行总线地址可以使用配置器功能进行分配。IC697BEM731总线控制器在安装时执行自我诊断，并具有LED灯指示灯，可显示操作和通信状态更新

GE Fanuc 90-70系列IC697BEM731总线控制器模块可以使用LAN连接到其他总线控制器模块和PCIM，它将充当这些设备和LAN的通信节点。它的默认波特率为 153.5 k波特。IC697BEM731总线控制器模块可以配置为处理全局通信应用。该模块只能在断电时安装在90-70系列PLC系统中，以避免组件损坏或严重伤害。它有 1 个串行端口，这是一个 HHM 或手持显示器端口，允许它连接到用户可以握在手中的显示器，这将为他们提供有关总线控制器模块、其应用以及系统中可能发生的任何故障或错误的实时视觉更新。

IC697BEM731 总线控制器模块 天才总线控制器

【英文介绍】

Product description

The IC697BEM731 is a Bus controller module (BCM) manufactured by GE Fanuc for the 90-70 series. The IC697BEM731 is designed for the Genius I/O handheld display IC660/IC661. The IC697BEM731 module can be used as a single channel controller; It therefore occupies only a single handheld display (IC66*) PLC slot. This BCM asynchronously scans the IC66* input/output module; Thus, once per scan, I/O data is transmitted to the CPU via the backplane of the IC697 PLC rack. The IC697BEM731 BCM is also responsible for supporting directed communication from PLC CPU communication service requests. In addition, it can be configured to perform global communication. The IC697BEM731 can only be configured via the MS DOS or Windows programming software configuration feature.

Other features of the IC697BEM731 include 30 voltage drops per channel, IC66* or IC661 I/O diagnostics, support for redundant blocks, cable and CPU, LAN communication, CPU soft configuration, and alarm processor capabilities. Please refer to the applicable PLC installation manual before installation. Power should be turned off before starting. Follow the instructions to install the rack, then turn on the power. If done correctly, the module will be powered on by the corresponding blinking LED. When the configuration is received from the CPU and the bus operation is verified, the intermediate LED will emit ON. The light at the bottom is always off.

Technical specification

Module type: Genius Bus controller

Effective data rate: Not applicable

Nooooo. Number of channels: 1

Drops per channel: 30

Serial port: 1 (handheld display port)

Current requirement: 1.3 amps

The physical communication cable used to establish the network is the Belton 9182 cable with GE catalog number IC660BLC001,15 inches, quantity 3, and IC660BLC003,36 inches, quantity 1. Bus terminator plugs must be installed at both ends of the bus, catalog number IC660BLM506 150 ohms, number 4 and IC660BLM508 75 ohms, number 4 resistors.

The IC697BEM731 bus controller supports global data transfer between cpus via a Windows-based software configuration, and can be enhanced with the IC697 PLC alarm system to report time-stamped failures on the processor's data table. The rear end of the bus controller module has a handheld monitor port for connecting the handheld monitor device, and a connector for establishing the IC66 bus connection. The IC697BEM731 bus controller is configured with Windows or MS-DOs-based configurator functionality. By default, the Windows-based configurator feature sets the baud rate to 153.5 Kilo-Bauds and the serial bus address to 31. Other baud rates and serial bus addresses can be assigned using the configurator function. The IC697BEM731 bus controller performs self-diagnosis at installation and has LED light indicators that show operational and communication status updates

GE Fanuc 90-70 Series IC697BEM731 bus controller modules can be connected to other bus controller modules and PCIM using a LAN, which will act as a communication node between these devices and the LAN. Its default baud rate is 153.5k baud. The IC697BEM731 Bus controller module can be configured to handle global communication applications. The module can only be installed in the 90-70 series PLC system in case of power failure to avoid component damage or serious injury. It has 1 serial port, which is an HHM or handheld display port, allowing it to connect to a display that the user can hold in their hand, which will give them real-time visual updates about the bus controller module, its application, and any faults or errors that may occur in the system.

IC697BEM731 总线控制器模块 天才总线控制器

【其他型号推荐】