GE  IC697ALG321 固态输入接口 简化故障排除程序

【产品详情】

GE Fanuc IC697ALG321模拟输入模块是由GE Fanuc设计和制造的90-70系列固态输入接口，旨在使工业机器用户能够减少布线安装时间并简化故障排除程序。它带有 4 个独立的电压通道，可以连接到与 GE Fanuc 90-70 系列控制架构兼容的任何类型的执行器、指示器或转换器。GE Fanuc IC697ALG321模拟输入模块通过插入GE Fanuc可编程逻辑控制器背板上的任何可用插槽来安装，该插槽应与电源断开连接以避免电弧，因为不支持热插拔操作。当IC697ALG321模拟输入模块正确安装到位时，技术人员将听到咔嗒声。所有接线连接都直接连接到单独的端子板中，而不是连接到该模拟输入模块中。

IC697ALG321模拟输入模块是GE发那科的高级模拟电压输入模块。它属于GE PLC或可编程逻辑控制器的90-30系列产品线。它允许单极性和双极性电压输入范围。用户还可以为两个范围设置报警限值，例如报警上限或报警下限。MS-DOS 配置软件提供了为其主机系统配置模块参数所需的所有功能，例如通道配置、模式选择、报警设置、范围选择和 I/O 扫描集配置设施。转换后的模拟数据以2的补码格式存储在PLC的CPU上。它还具有状态位，这些状态位返回到PLC的CPU，以提供有关模块操作的数据。

IC697ALG321模拟输入模块的输入滤波器响应频率在单端模式下为 41 赫兹，在差分模式下为 82 赫兹。接收到的数据信号将通过12位转换器转换为数字信号，以便在PLC的CPU中进行处理。为了获得分辨率和准确性，转换后的数据也将放置在16位WORD格式中。CPU不会更改输入中的任何接收值，而是在放入WORD格式之前根据需要直接转换和处理信号。用户可以使用 Logicmaster 软件或手持编程器提供的界面轻松执行模块的基本配置。请注意，手持式编程器不提供配置活动扫描通道的工具。所有配置数据将保存在PLC中CPU的EEPROM中。

GE Fanuc IC697ALG321模拟输入模块由坚硬耐用的塑料制成，出厂时采用开放式外壳，无法或旨在提供足够的防高湿度保护或防止灰尘或水进入设备。GE Fanuc IC697ALG321模拟输入模块应安装在适当保护的外壳内，以保持其清洁和安全，并保持在制造商推荐的环境参数范围内，以实现无故障运行。该模块的电压输入范围在 -10 至 +10 伏交流电之间，分辨率为 16 位，转换速率为 2 毫秒。

GE  IC697ALG321 固态输入接口 简化故障排除程序

【英文介绍】

The GE Fanuc IC697ALG321 analog input module is a series 90-70 solid state input interface designed and manufactured by GE Fanuc to enable industrial machine users to reduce cabling installation time and simplify troubleshooting procedures. It comes with 4 separate voltage channels that can be connected to any type of actuator, indicator or converter compatible with GE Fanuc 90-70 series control architecture. The GE Fanuc IC697ALG321 analog input module is installed by plugging into any available slot on the GE Fanuc programmable Logic Controller backplane, which should be disconnected from the power supply to avoid arcing, as hot-swap-operation is not supported. When the IC697ALG321 analog input module is properly installed in place, the technician will hear a clicking sound. All wiring connections are connected directly to individual terminal boards rather than to the analog input module.

The IC697ALG321 analog input module is GE Fanuc's advanced analog voltage input module. It belongs to GE's 90-30 series of PLC or programmable logic controllers. It allows unipolar and bipolar voltage input ranges. Users can also set alarm limits for two ranges, such as upper or lower alarm limits. MS-DOS configuration software provides all the features needed to configure module parameters for its host system, such as channel configuration, mode selection, alarm Settings, range selection, and I/O scan set configuration facilities. The converted analog data is stored on the PLC CPU in 2 complement format. It also has status bits that are returned to the PLC's CPU to provide data about module operations.

The input filter response frequency of the IC697ALG321 analog input module is 41 Hz in single-ended mode and 82 Hz in differential mode. The received data signal is converted to a digital signal by a 12-bit converter for processing in the PLC's CPU. For resolution and accuracy, the converted data will also be placed in 16-bit WORD format. The CPU does not change any of the received values in the input, but converts and processes the signal directly as needed before putting it into WORD format. The basic configuration of the module can be easily performed by the user using the Logicmaster software or the interface provided by the handheld programmer. Note that the handheld programmer does not provide tools for configuring active scan channels. All configuration data will be saved in the EEPROM of the CPU in the PLC.

The GE Fanuc IC697ALG321 analog input module is made of hard and durable plastic and comes out of the factory with an open housing that cannot or is intended to provide adequate protection against high humidity or prevent dust or water from entering the device. The GE Fanuc IC697ALG321 analog input module shall be installed in a properly protected housing to keep it clean and safe and within the manufacturer's recommended environmental parameters for troup-free operation. The module has a voltage input range of -10 to +10 volts AC, a resolution of 16 bits and a conversion rate of 2 milliseconds.

GE  IC697ALG321 固态输入接口 简化故障排除程序

【其他型号推荐】