GE IC697ACC621 机架风扇组件

【产品详情】

IC697ACC621风扇组件是一种机架风扇组件，已由GE Fanuc Automation作为附件引入PLC的90-70系列产品线。该组件用于为系列中的不同机架提供额外的冷却，尤其是它们的连接和电子部件。过热是导致运行期间突然停止和导致系统出现问题的主要原因之一，最终导致损坏的部件需要维修或更换。此机架风扇组件旨在连接到安装在通风很少且容易过热的地方的机架上。GE Fanuc 自动化IC697ACC621机架风扇组件以 120 伏交流电的电压运行，在相同电压下每个风扇的输入功率为 15 至 20 瓦。

IC697ACC621是与GE系列90-70 PLC配合使用的风扇托盘组件。 这种特殊的风扇托盘提供了一个额外的机架冷却系统，每个组件有两个风扇。机架风扇可作为附件轻松安装到五插槽和 PACSystems RX7i 九插槽机架中。该IC697ACC621非常适合存在潜在热量积聚问题的系统。该系统噪音低，并使用滚珠轴承延长使用寿命。制造商建议将风扇连接到与 PLC 相同的电源，因为这将确保风扇在每次 PLC 处于活动使用状态时运行。

要连接风扇，请使用风扇随附的并行电缆组件，该组件位于风扇组件的背面。IC697ACC621风扇托盘与IC697CHS750架、IC698CHS009架和IC697CHS109架兼容。当安装在机架上时，该装置位于底部，以允许空气从机架底部流向顶部进行冷却。

只需一把#2十字头螺丝刀即可轻松完成安装。机架之间至少需要 9 英寸的空间来卸下每个单独的风扇，可以通过从机架的前下方面板上卸下三个螺钉来完成。只需将风扇组件放在底部机架上，然后滑动组件背面的法兰即可。对齐孔，重新安装并拧紧螺钉。每个风扇都有一个可更换的聚氨酯过滤器，如果需要，可以在两次更换之间进行清洁。

GE Fanuc 自动化IC697ACC621机架风扇组件与 9 插槽 RX7i 机架和 5 插槽 90-70 系列机架兼容。该组件的锁定转子电流范围为 0.24 至 0.34 安培，仅重 4 磅。此组件包括 2 个风扇。GE Fanuc自动化IC697ACC621机架风扇组件配有聚氨酯泡沫过滤器，设计为每平方英寸30个孔，以及塑料UL94V-0固定器和防护装置。风扇组件在运行时具有低噪音水平，并且使用滚珠轴承来延长使用寿命。工作温度范围为 028 至 70 摄氏度。建议将此设备安装在干净的地方，以免过滤器堵塞。

GE IC697ACC621 机架风扇组件

【英文介绍】

The IC697ACC621 fan assembly is a rack fan assembly that has been introduced as an accessory to the PLC's 90-70 series product line by GE Fanuc Automation. This component is used to provide additional cooling for the different racks in the series, especially their connections and electronic components. Overheating is one of the main causes of sudden stops during operation and causes problems with the system, eventually leading to damaged parts requiring repair or replacement. This rack fan assembly is designed to be attached to racks installed in areas with little ventilation and prone to overheating. GE Fanuc Automation IC697ACC621 Rack fan assemblies operate at 120 volts AC, with input power of 15 to 20 watts per fan at the same voltage.

The IC697ACC621 is a fan tray assembly for use with GE series 90-70 PLCS. This special fan tray provides an additional rack cooling system with two fans per component. Rack fans can be easily installed as accessories into five-slot and PACSystems RX7i nine-slot racks. The IC697ACC621 is ideal for systems with potential heat build-up problems. The system is low noise and uses ball bearings for extended service life. Manufacturers recommend connecting the fan to the same power source as the PLC, as this will ensure that the fan runs every time the PLC is in active use.

To connect the fan, use the parallel cable assembly that came with the fan, which is located on the back of the fan assembly. The IC697ACC621 fan tray is compatible with the IC697CHS750, IC698CHS009 and IC697CHS109. When mounted on a rack, the unit is located at the bottom to allow air to flow from the bottom of the rack to the top for cooling.

Easy installation with a #2 crosshead screwdriver. A minimum of 9 inches of space is required between the racks to remove each individual fan, which can be done by removing three screws from the front and lower panels of the racks. Simply place the fan assembly on the bottom rack and slide the flange on the back of the assembly. Align the holes, reinstall and tighten the screws. Each fan has a replaceable polyurethane filter that can be cleaned between changes if needed.

GE Fanuc Automation IC697ACC621 Rack fan assemblies are compatible with 9-slot RX7i racks and 5-slot 90-70 series racks. The assembly has a locking rotor current range of 0.24 to 0.34 amps and weighs just 4 pounds. This assembly includes 2 fans. The GE Fanuc Automation IC697ACC621 rack fan assembly features a polyurethane foam filter designed for 30 holes per square inch, as well as a plastic UL94V-0 holder and guard. The fan assembly has a low noise level during operation and uses ball bearings for extended service life. Operating temperature range is 028 to 70 degrees Celsius. It is recommended to install this device in a clean place to avoid clogging the filter.

GE IC697ACC621 机架风扇组件

【其他型号推荐】