IC693CBL313 GE  I/O 总线扩展电缆

【产品详情】

GE Fanuc IC693CBL313是一根 I/O 总线扩展电缆。这是总线扩展电缆系列的一个部件号，也称为“星形电缆”。其他包括IC693CBL300、301、312和314。I/O 总线扩展电缆的两端都有一个 25 针 D 连接器。在一端，它是一个单公连接器，而另一端是一个双头连接器——一个公头和一个母头。IC693CBL313电缆长 25 英尺，约 8 米。 I/O 总线扩展电缆的目的是将 I/O 总线扩展到 90-30 系列 I/O 系统中的扩展或远程底板。当需要额外的 I/O 插槽或需要与 CPU 底板保持一定距离的底板时，使用电缆。

用户可以将扩展底板或远程底板连接到预接线的 I/O 总线扩展电缆。一个 I/O 扩展系统一次最多可以有七根电缆。CPU 底板和最远扩展板之间的最大电缆长度不得超过 50 英尺（15 米）。但是，允许在 CPU 底板和最后一个远程底板之间延长 700 英尺（213 米）的长度。如果不遵守这些最大电缆长度准则，PLC 系统可能无法正常工作。用户必须注意在 I/O 扩展底板通电时不要连接或断开任何电缆。

GE Fanuc IC693CBL313 I/O 总线扩展电缆是用于 GE 系列 90-30 PLC 系统的 I/O 扩展基础电缆组件。IC693CBL313电缆是一种星形 I/O 扩展电缆，具有连续电线屏蔽，旨在通过“菊花链”配置或远程底板将 CPU 基板与扩展基板互连。IC693CBL313 I/O 总线扩展电缆提供 25 英尺（8 米）的最大布线长度。它由一个 25 针 D 型公连接器、一个双头连接器（一个公头和一个母头）、一个 8 米（25 英尺）连续屏蔽星形电缆和一个安装表组成。当需要将额外的 I/O 插槽或底板连接到与 CPU 底板一定距离的距离时，此电缆可用于扩展 90-30 系列 I/O 系统中的 I/O 扩展或远程底板功能（通过“菊花链”配置）。

IC693CBL313 I/O 总线扩展电缆有 2 个连接器端。8 米电缆的一端是一个 25 针公连接器，另一端是一个双头连接器，由 1 个 25 针公连接器和 1 个 25 针母连接器组成。电缆单连接器端的 25 针公连接器连接到 CPU 底板上的 25 针母连接器。双头端的公连接器连接到下一个扩展或远程底板上的 25 针母连接器，双头端的母连接器连接到下一个扩展底板上的公连接器以继续“菊花链”链路，或者如果它是链条上的最后一根电缆，则通过 I/O 总线端接器插头端接。

IC693CBL313 GE  I/O 总线扩展电缆

【英文介绍】

The GE Fanuc IC693CBL313 is an I/O bus expansion cable. This is a part number of the bus extension cable family, also known as the "star cable". Others include IC693CBL300, 301, 312 and 314. Both ends of the I/O bus expansion cable have a 25-pin D connector. At one end, it is a single male connector, while the other end is a double-ended connector - a male and a female. The IC693CBL313 cable is 25 feet long, about 8 meters. The I/O bus expansion cable is designed to extend the I/O bus to an extension or remote backboard in a 90-30 series I/O system. Cables are used when additional I/O slots are needed or when a backboard is needed at a certain distance from the CPU backboard.

Users can connect the expansion backboard or remote backboard to a pre-wired I/O bus expansion cable. An I/O expansion system can have up to seven cables at a time. The maximum cable length between the CPU baseboard and the farthest expansion board must not exceed 50 feet (15 meters). However, a length extension of 700 feet (213 m) is allowed between the CPU backboard and the last remote backboard. If these maximum cable length guidelines are not followed, the PLC system may not function properly. Users must take care not to connect or disconnect any cables while the I/O expansion baseboard is energized.

The GE Fanuc IC693CBL313 I/O bus expansion cable is an I/O expansion base cable assembly for GE series 90-30 PLC systems. The IC693CBL313 cable is a star-shaped I/O expansion cable with continuous wire shielding designed to interconnect the CPU substrate with the expansion substrate through a "Daisy chain" configuration or remote backboard. The IC693CBL313 I/O bus expansion cable offers a maximum wiring length of 25 feet (8 meters). It consists of a 25-pin D-type male connector, a double-ended connector (one male and one female), an 8-meter (25 ft) continuous shielded star cable, and a mounting table. When additional I/O slots or backboards need to be connected to a certain distance from the CPU backboard, this cable can be used to extend I/O expansion or remote backboard functionality in Series 90-30 I/O systems (via a "Daisy chain" configuration).

The IC693CBL313 I/O bus expansion cable has 2 connector ends. One end of the 8-meter cable is a 25-pin male connector, and the other end is a double-ended connector consisting of a 25-pin male connector and a 25-pin female connector. The 25-pin male connector at the single-connector end of the cable is connected to the 25-pin female connector on the CPU baseboard. The double-ended male connector connects to the 25-pin female connector on the next extension or remote baseboard, and the double-ended female connector connects to the male connector on the next extension baseboard to continue the "Daisy chain" link, or if it is the last cable on the chain, terminating via the I/O bus terminator plug.

IC693CBL313 GE  I/O 总线扩展电缆

【其他型号推荐】