GE Fanuc  IC693CBL303 HHP和转换器电缆

【产品详情】

IC693CBL303是GE Fanuc系列90-30 PLC的HHP和转换器电缆。它长 6 英尺，将手持式编程器与可编程逻辑控制器连接起来。它的每一端都有一个 15 针公头 D 超小型和佳能 DA15 型连接器。电缆类型为百通 8508，配有连接器外壳、公制螺钉和螺钉夹。要使用 IC693CBL303 HHP 和转换器电缆，请将 15 针 D 连接器连接到 PLC 的串行端口。另一端连接到 HPP 底部的配接连接器。连接 HPP 时，电缆将提供电源并向 PLC 发送信号。

除了GE Fanuc IC693CBL303 HHP和90-30系列转换器电缆之外，还可以创建定制电缆。 如果是这种情况，它可以长达 300 英尺，并且需要单独的电源。定制电缆所需的电缆类型是百通9309型电缆，并且需要+5 VDC的外部电源。9 针连接器的针脚 10 和 15 必须跳线。PLC电源的+5V和SG连接必须与电源线接地连接分离。电缆连接器的+5V引脚不得连接到PLC。GE Fanuc C693CBL303 HHP 和转换器电缆的另一个用途是将 PLC 连接到 RS-232 转换器。PLC可以通过RS-422串行端口或PC兼容计算机连接到编程器。

IC693CBL303电缆是一种手持式编程器电缆，已包含在GE Fanuc制造的PLC的90-30系列中。这种特殊的电缆是为了将手持式编程器（HHP）称为GE IC693PRG300手持式编程器）连接到PLC电源上的串行连接器。该电缆使HHP和可编程逻辑控制器或PLC能够相互通信以及与应用过程相关的不同设备进行通信。该电缆还提供与 HHP 的电源连接，以及向 PLC 指示 HHP 已正确连接到其串行端口的信号连接。GE Fanuc IC693CBL303手持式编程器电缆也可用于将 PLC RS-485 串行端口连接到 RS-422/485 到 RS-232 转换器。

GE Fanuc IC693CBL303手持式编程器电缆配有佳能DA15S连接器，该连接器由带有连接器外壳的15针公头D超小型连接器类型组成。该电缆的长度为2米，电缆类型为百通9508电缆，直径为.22平方毫米。如果需要不同的电缆长度，可以通过组合不同的元件来构建它，但如果长度过长，可能会导致电噪声并影响信号。GE Fanuc IC693CBL303手持编程器电缆的 15 针连接器必须连接到 PLC 电源上的串行端口连接器。然后，电缆另一端的 D 连接器必须连接到 HHP。为确保正常运行，必须在电缆的长度和直径之间正确计算长度，以避免电气干扰。

GE Fanuc  IC693CBL303 HHP和转换器电缆

【英文介绍】

The IC693CBL303 is an HHP and converter cable for GE Fanuc series 90-30 PLCS. It is 6 feet long and connects a handheld programmer to a programmable logic controller. It has a 15-pin male D subminiature and Canon DA15 type connector at each end. Cable type is Belton 8508 with connector housing, metric screws and screw clamps. To use the IC693CBL303 HHP and converter cable, connect the 15-pin D connector to the PLC's serial port. The other end is connected to the mating connector at the bottom of the HPP. When the HPP is connected, the cable will provide power and send a signal to the PLC.

In addition to the GE Fanuc IC693CBL303 HHP and 90-30 series converter cables, custom cables can also be created. If this is the case, it can be up to 300 feet long and requires a separate power source. The cable type required for the custom cable is the Belton 9309 cable and requires an external power supply of +5 VDC. Pins 10 and 15 of the 9-pin connector must be jumped. The +5V and SG connections of the PLC power supply must be separated from the power cable ground connection. The +5V pin of the cable connector must not be connected to the PLC. Another use of the GE Fanuc C693CBL303 HHP and converter cable is to connect the PLC to the RS-232 converter. The PLC can be connected to the programmer via the RS-422 serial port or a PC-compatible computer.

The IC693CBL303 cable is a handheld programmer cable that has been included in the 90-30 series of PLCS manufactured by GE Fanuc. This special cable is designed to connect a hand-held programmer (HHP) called GE IC693PRG300 Hand-held Programmer to a serial connector on the PLC power supply. The cable enables the HHP and the programmable logic controller or PLC to communicate with each other and with different devices related to the application process. The cable also provides a power connection to the HHP, as well as a signal connection to the PLC indicating that the HHP is properly connected to its serial port. The GE Fanuc IC693CBL303 handheld programmer cable can also be used to connect the PLC RS-485 serial port to the RS-422/485 to RS-232 converter.

The GE Fanuc IC693CBL303 handheld programmer cable is equipped with the Canon DA15S connector, which consists of a 15-pin male D subminiature connector type with a connector housing. The length of the cable is 2 meters, the cable type is Betong 9508 cable, and the diameter is.22 square millimeters. If a different cable length is required, it can be built by combining different elements, but if it is too long, it may cause electrical noise and affect the signal. The 15-pin connector of the GE Fanuc IC693CBL303 handheld programmer cable must be connected to the serial port connector on the PLC power supply. The D connector on the other end of the cable must then be connected to the HHP. To ensure normal operation, the length must be calculated correctly between the length and diameter of the cable to avoid electrical interference.

GE Fanuc  IC693CBL303 HHP和转换器电缆

【其他型号推荐】