GE Fanuc IC693CBL301 输入或输出扩展电缆

【产品详情】

GE Fanuc IC693CBL301是一种输入或输出扩展电缆，也称为星形电缆。该电缆的长度为 6 英尺，带有连续屏蔽。IC693CBL301一端配有一个 25 针公连接器，另一端配有一个双头连接器。该扩展电缆用于将输入或输出总线扩展到 90-30 系列 PLC 系统中的扩展基板。当标准电缆没有系统所需长度时，定制电缆是必要的。

安装IC693CBL301膨胀电缆时，超过规定的电缆长度，这会导致90-30系列PLC系统中的不稳定运行，因此应避免这种情况。用户应始终验证系统内组件的规格。此外，在扩展系统中，用户最多可以使用七根兼容电缆。CPU 基板和最终远程底板之间允许的最大电缆长度为 700 英尺，CPU 基板和最终扩展板之间的电缆长度为 50 英尺。

使用标准IC693CBL301扩展电缆可节省时间并避免不必要的接线错误。IC693CBL301扩展电缆可以使用两种不同类型的定制电缆。第一个是“点对点电缆”。此电缆的一端有一个公连接器，另一端有一个母连接器。第二根电缆被称为“星形电缆”。它由一端的公连接器和另一端的公连接器和母连接器组成。与星形电缆相比，点对点电缆的构建速度更快。

IC693CBL301是总线扩展电缆，是GE Fanuc Automation（目前隶属于艾默生自动化）的90-30系列产品系列的一部分。该电缆主要用于通过使用IC693CBL301电缆将扩展或远程基板互连到 CPU 基板的扩展端口来实现 I/O 扩展。此电缆也称为星形电缆，一端具有一 （1） 个 25 针连接器，另一端具有一 （1） 个公头和一 （1） 个 25 针母头连接器。IC693CBL301的电缆长度为 6 英尺或 2 米，具有连续屏蔽。连接此电缆时，25 针连接器连接到位于最右侧的 CPU 扩展端口。电缆的公连接器连接到位于最左侧的扩展或远程底板的 25 针母连接器。裸露的 25 针连接器可用于连接到另一个 I/O 总线扩展以进行进一步互连，或连接到终结器插头以关闭 I/O 总线。单个 7-90 系列系统最多可使用七 （30） 个电缆实例。CPU 底板与最后一个扩展底板之间的最大总电缆长度不得超过 50 英尺或 15 米，或者从 CPU 到最后一个远程底板之间的最大总电缆长度不得超过 700 英尺或 213 米。未端接的扩展总线或 I/O 总线长度超过建议的测量值将导致不稳定的通信和 I/O 数据交换。使用 CPU 350 - 364 时，最多支持 7 根扩展电缆，而使用 CPU 331-314，最多允许 4 根扩展电缆。

IC693CBL301电缆是一种I/O总线扩展电缆，由GE Fanuc设计和制造，包含在GE系列90-30中。这种特殊的电缆在不同机架和CPU之间提供连接，在不同扩展端口之间提供均匀的互连。此特定型号还用作星形电缆类型，用于将不同的底板或机架菊花链连接在一起。该电缆的结构提供连续屏蔽功能。当需要额外的I/O插槽或出于设计或安全原因需要将不同的底板与主CPU保持一定距离时，GE Fanuc IC693CBL301 I/O总线扩展电缆可以将I/O总线扩展到系统中的扩展或远程机架。除其他外，该电缆用于构建定制电缆，该电缆可以帮助实现所需的长度而不会失去有效性。

GE Fanuc IC693CBL301 I/O 总线扩展电缆两端都带有连接器。这些连接器由一个 25 针公连接器和另一端的 2 个公/母 25 针连接器组成。两个连接器都是 D 型连接器。要连接多根电缆，用户需要首先连接CPU底板右侧的单公连接器。然后要连接第二个底板，需要将双连接器端的公连接器连接到第一根扩展电缆上的母针连接器。双端未使用的母连接器可以连接到第二根 I/O 总线扩展电缆或 I/O 总线终结器插头的单公连接器。GE Fanuc IC693CBL301 I/O 总线扩展电缆的长度为 2 米。

GE Fanuc IC693CBL301 输入或输出扩展电缆

【英文介绍】

The GE Fanuc IC693CBL301 is an input or output expansion cable, also known as a star cable. The cable is 6 feet in length with continuous shielding. The IC693CBL301 has a 25-pin male connector at one end and a double-ended connector at the other end. The expansion cable is used to extend the input or output bus to the expansion substrate in the 90-30 series PLC system. Custom cables are necessary when standard cables do not have the required length of the system.

When installing the IC693CBL301 expansion cable, exceeding the specified cable length can cause unstable operation in the 90-30 series PLC system, so this should be avoided. Users should always verify the specifications of the components within the system. In addition, in the extended system, users can use up to seven compatible cables. The maximum allowable cable length between the CPU substrate and the final remote backboard is 700 feet, and the cable length between the CPU substrate and the final expansion board is 50 feet.

Use the standard IC693CBL301 expansion cable to save time and avoid unnecessary wiring errors. The IC693CBL301 expansion cable can use two different types of custom cables. The first is "point-to-point cable." This cable has a male connector at one end and a female connector at the other end. The second cable is called the "star cable". It consists of a male connector at one end and a male connector and female connector at the other end. Point-to-point cables are built faster than star-shaped cables.

The IC693CBL301 is a bus expansion cable that is part of the 90-30 series product family from GE Fanuc Automation (now part of Emerson Automation). The cable is primarily used to enable I/O expansion by interconnecting the expansion or remote substrate to the expansion port of the CPU substrate using the IC693CBL301 cable. This cable, also known as a star cable, has one (1) 25-pin connector at one end and one (1) male and one (1) 25-pin female connector at the other end. The IC693CBL301 has a cable length of 6 feet or 2 meters with continuous shielding. When connecting this cable, the 25-pin connector is connected to the CPU expansion port located on the far right. The male connector of the cable is connected to a 25-pin female connector located on the far left side of the extension or remote baseplate. The bare 25-pin connector can be used to connect to another I/O bus extension for further interconnection, or to a terminator plug to close the I/O bus. A single 7-90 series system can use up to seven (30) cable instances. The maximum total cable length between the CPU baseboard and the last expansion baseboard must not exceed 50 feet or 15 meters, or the maximum total cable length between the CPU and the last remote baseboard must not exceed 700 feet or 213 meters. An unterminated expansion bus or I/O bus length exceeding the recommended measured value will result in unstable communication and I/O data exchange. With CPU 350-364, up to 7 expansion cables are supported, while with CPU 331-314, up to 4 expansion cables are allowed.

The IC693CBL301 cable is an I/O bus expansion cable designed and manufactured by GE Fanuc and included in the GE Series 90-30. This special cable provides connections between different racks and cpus, providing uniform interconnections between different expansion ports. This particular model is also used as a star cable type for connecting different baseboards or rack Daisy chains together. The structure of the cable provides continuous shielding. The GE Fanuc IC693CBL301 I/O Bus expansion cable can extend the I/O bus to an extension or remote rack in the system when additional I/O slots are required or when different backboards need to be kept at a distance from the main CPU for design or security reasons. Among other things, the cable is used to build custom cables that can help achieve the desired length without losing effectiveness.

The GE Fanuc IC693CBL301 I/O bus expansion cable has connectors at both ends. These connectors consist of a 25-pin male connector and two male/female 25-pin connectors on the other end. Both connectors are D-type connectors. To connect multiple cables, users need to first connect the single male connector on the right side of the CPU baseboard. Then to connect the second baseplate, you need to connect the male connector on the double connector end to the female pin connector on the first expansion cable. A double-ended unused female connector can be connected to a second I/O bus expansion cable or a single male connector of the I/O bus terminator plug. The length of the GE Fanuc IC693CBL301 I/O bus expansion cable is 2 meters.

GE Fanuc IC693CBL301 输入或输出扩展电缆

【其他型号推荐】