GE IC695PSD140 RX3i电源模块 直流电源

【产品详情】

IC695PSD140是由艾默生自动化制造的PACSystems RX3i电源模块，前身由GE智能平台（GE IP）制造。该模块专门用于直流电源，设计用于 18-30 VDC 的输入电压范围和满载时的最大输入功率为 60 瓦。它的标称输出电流和电压为 0-6 A @ 5.1 VDC 和 0-9 A @ 3.3 VDC。它还具有用于电源电路和输出继电器模块的 24VDC 电压输出，最大输出功率为 40 瓦。该模块支持负载共享和冗余应用。

IC695PSD140是艾默生自动化制造的电源模块，是 PACsystem RX3i PAC 平台的一部分。该模块专门用于通用基础电源，可与任何 RX3i 中央处理器 （CPU） 兼容。此模块没有跳线或 DIP 开关来定义模块的操作。

IC695PSD140占用机箱的两 （2） 个插槽。它由 100-240 VAC 或 0-125 VDC 的外部电源电压供电，在 40.30 VDC 时提供额定输出功率 3 瓦和 3 瓦;30VDC 时为 5 瓦，40 VDC 继电器时为 24 瓦。RX4i 通用背板上最多可安装四 （3） 个多用途电源，用于需要冗余和增加容量模式的应用。

在负载共享架构中配置时，安装在前面板上的IC695PSD140开/关开关不得无意中关闭。必须保持最小数量的电源打开才能使系统合格。此外，对于相同的配置，电源模块必须连接到同一电源。

该电源的输出纹波为150 mV，噪声测量值为150 mV，穿越时间为20 ms。功率穿越时间是指电源在电源线中断的情况下提供足够电力的能力。终止与电源端子的连接时，建议的电线尺寸范围为 #14 - 22 AWG 电线。每个输入端子可容纳的最大电流为 6 安培。

IC695PSD140模块是RX3i PACSystems系列I/O设备中的多用途电源模块。该部件由GE Fanuc Automation设计和制造。该模块可以在负载共享和冗余应用中运行，因此具有多用途标签。它带有 3 个不同的输出，包括 5.1 伏直流输出、24 伏直流继电器输出和 3.3 伏。供内部使用的伏直流输出。这 3 个输出可与 RX3i 模块配合使用。GE Fanuc自动化IC695PSD140多用途电源模块可以安装在RX3i通用背板上，并且仅占用一个插槽。它可以用作系统中唯一的电源，也可以与其他多用途电源结合使用。它最多可以与 3 个其他模块结合使用。

GE IC695PSD140 RX3i电源模块 直流电源

【英文介绍】

The IC695PSD140 is a PACSystems RX3i power module manufactured by Emerson Automation and formerly manufactured by GE Intelligent Platforms (GE IP). The module is specifically designed for DC power and is designed for an input voltage range of 18-30 VDC and a maximum input power of 60 watts at full load. Its nominal output current and voltage are 0-6A@ 5.1VDC and 0-9A@ 3.3VDC. It also has a 24VDC voltage output for the power circuit and output relay module, with a maximum output power of 40 watts. The module supports load sharing and redundant applications.

The IC695PSD140 is a power module manufactured by Emerson Automation and is part of the PACsystem RX3i PAC platform. The module is designed for general purpose base power supplies and is compatible with any RX3i central processing unit (CPU). This module does not have a jumper or DIP switch to define the module's operation.

The IC695PSD140 occupies two (2) slots in the chassis. It is powered by an external supply voltage of 100-240 VAC or 0-125 VDC, providing rated output power of 3 watts and 3 watts at 40.30 VDC; 5 watts at 30VDC and 24 watts at 40 VDC relays. Up to four (3) multi-purpose power supplies can be installed on the RX4i universal backplane for applications requiring redundancy and increased capacity modes.

When configured in a load sharing architecture, the IC695PSD140 on/off switch installed on the front panel must not be unintentionally turned off. A minimum amount of power must be kept on for the system to qualify. In addition, for the same configuration, the power module must be connected to the same power supply.

The output ripple of this power supply is 150 mV, the noise measurement is 150 mV, and the crossing time is 20 ms. Power crossing time refers to the power supply's ability to provide sufficient power in the event of a power line interruption. When terminating the connection to the power terminal, the recommended wire size range is # 14-22 AWG wire. Each input terminal can hold a maximum current of 6 amps.

The IC695PSD140 module is a multipurpose power module in the RX3i PACSystems series of I/O devices. The part was designed and manufactured by GE Fanuc Automation. The module can run in load sharing and redundancy applications, so it has multi-purpose labels. It comes with 3 different outputs, including 5.1 volts DC output, 24 volts DC relay output, and 3.3 volts. Volt DC output for internal use. These three outputs can be used with the RX3i module. The GE Fanuc Automation IC695PSD140 multipurpose power module can be installed on the RX3i universal backplane and occupies only one slot. It can be used as the only power supply in the system or in combination with other multi-purpose power supplies. It can be combined with up to 3 other modules.

GE IC695PSD140 RX3i电源模块 直流电源

【其他型号推荐】