GE IC695PNC001 RX3i通信模块 通用A类IO控制器

【产品详情】

该IC695PNC001是由艾默生自动化制造的PACSystems RX3i通信模块，前身为GE智能平台（GE IP）。该模块是一个PROFINET控制器模块，用于将RX3i系统连接到PROFINET网络。它支持PROFINET 2.2版通用A类IO控制器，兼容CPU315或CPU320，固件版本为7.0或更高版本。每个PROFINET控制器最多支持64个设备，每个网络最多可以连接8个I/O控制器。最多可以连接 2048 个 I/O 设备或每个网络 128 个 PROFINET 控制器。该模块有两个 RJ-45 和两个 SFP 插槽和一个微型 USB 连接器。

IC695PNC001是一个PROFINET控制器模块。该模块以前由GE智能平台（GE IP）制造，现在由艾默生自动化制造。该PROFINET控制器使RX3i CPU能够通过PROFINET网络发送和接收数据。

该IC695PNC001兼容固件版本为3.315或更高版本的PACSystem RX320i CPU7或CPU0。此模块随附两 （2） 个 RJ-45 和两 （2） 个带 SFP 连接器的 SFP 插槽，单独出售。只为这些PROFINET端口分配一个IP地址。最多可以沿单个 CPU 安装四 （4） 个IC695PNC001，并且必须仅位于 CPU 所在的主机架上。最多六十四 （64） 个 I/O 设备可以连接到一 （1） 个控制器;每个网络 128 个 I/O 设备，分布在八 （8） 个 I/O 控制器中。此外，单个网络中最多可以安装八 （8） 个 I/O 设备。该模块具有可配置的数据更新时间，分别为 1 ms、2 ms、4 ms、8 ms、16 ms、32 ms、64 ms、128 ms、256 ms 和 512 ms。

IC695PNC001控制器是由GE智能平台/GE Fanuc PACSystems制造的PROFINET控制器，是RX3i系列的一部分。该PROFINET控制器模块有助于将RX3i PacSystems系列中的控制器连接到高速PROFINET LAN。它的一些值得注意的规格包括单插槽，仅支持通用背板，以及PROFINET 2.2通用A类网络额定值。它在 1 伏直流电时以 5.5 安培的内部功率工作，或在 0.5 伏直流电的额定电压下以 3.3 安培的内部功率工作。IC695PNC001 PROFINET控制器模块的工作温度范围为0至60摄氏度，但根据PNC001位置和SFP的人口，可能需要较低的温度。该模块具有 1 个微型 USB 连接器，用于通过命令行界面与计算机通信。它还具有 2 个 SFP 笼和 2 个 RJ-45 端口连接器，但 SFP 设备可以单独购买。

GE IC695PNC001 RX3i通信模块 通用A类IO控制器

【英文介绍】

The IC695PNC001 is a PACSystems RX3i communication module manufactured by Emerson Automation and formerly known as GE Intelligence Platform (GE IP). This module is a PROFINET controller module for connecting the RX3i system to the PROFINET network. It supports PROFINET version 2.2 General Purpose Class A IO controllers, compatible with CPU315 or CPU320, with firmware version 7.0 or higher. Each PROFINET controller supports up to 64 devices, and each network can connect up to eight I/O controllers. You can connect up to 2048 I/O devices or 128 PROFINET controllers per network. The module has two RJ-45s and two SFP slots and a micro-USB connector.

IC695PNC001 is a PROFINET controller module. The module was previously manufactured by GE Intelligent Platform (GE IP) and is now manufactured by Emerson Automation. The PROFINET controller enables the RX3i CPU to send and receive data over the PROFINET network.

The IC695PNC001 is compatible with firmware version 3.315 or later PACSystem RX320i CPU7 or CPU0. This module comes with two (2) RJ-45s and two (2) SFP slots with SFP connectors and is sold separately. Only one IP address is assigned to these PROFINET ports. Up to four (4) IC695PNC001s can be installed along a single CPU and must be located only on the host shelf where the CPU is located. Up to sixty-four (64) I/O devices can be connected to one (1) controller; There are 128 I/O devices per network, distributed among eight (8) I/O controllers. In addition, up to eight (8) I/O devices can be installed in a single network. The module has configurable data update times of 1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms and 512 ms.

The IC695PNC001 controller is a PROFINET controller manufactured by GE Intelligent Platforms /GE Fanuc PACSystems and is part of the RX3i family. The PROFINET controller module helps connect controllers in the RX3i PacSystems family to a high-speed PROFINET LAN. Some of its notable specifications include single slot, universal backplane support only, and PROFINET 2.2 Universal Class A network rating. It operates at an internal power of 5.5 amps at 1 volt DC, or 3.3 amps at a rated voltage of 0.5 volts DC. The IC695PNC001 PROFINET controller module operates in a temperature range of 0 to 60 degrees Celsius, but depending on the PNC001 location and the population of the SFP, lower temperatures may be required. The module has a micro USB connector for communicating with the computer via a command line interface. It also features 2 SFP cages and 2 RJ-45 port connectors, but SFP devices can be purchased separately.

GE IC695PNC001 RX3i通信模块 通用A类IO控制器

【其他型号推荐】