GE IC694TBB132 高密度扩展盒式接线端子

【产品详情】

IC694TBB132是一款 36 针高密度扩展盒式接线端子，可与 PACSystem RX32i 可编程自动化控制器 （PAC） 系列以及等效的 3-90 系列 PLC 平台的 30 个输入 I/O 模块配合使用。该接线端子目前由艾默生自动化制造，以前由GE智能平台（GE IP）制造。IC694TBB132具有标准深度输出盖，尺寸为 23 毫米或 0.9 英寸。端子设计为端接 #14-26 美国线规 （AWG）、实心或绞合铜线的电线尺寸范围。带状线端的长度为 0.310 英寸，为 7.87 毫米。接线端子的底部设计为参考推荐的电线条长度。施加到每个连接点的推荐拧紧扭矩为 7 lb-inch。要将IC694TBB132盒式接线端子安装到其盖子上，请将接线端子的顶部与盖子的底部对齐。检查盖板和端子上的凹槽和凹槽。它们必须对齐，以确保接线端子完美地卡入模块。对齐后，向上滑动接线端子，直到听到咔嗒声。如果在插入过程中感觉到阻力，请不要用力插入模块，而是拔出并重新检查对齐和可能的障碍物，然后再重试。一旦与盖子一起安装，组件现在可以连接到主模块。将组件与模块的前面板端口对齐。将端子组件垂直按向模块，直到就位。打开前盖并向后推闩锁，将组件锁定到位。

IC694TBB132接线端子是GE发那科生产的盒装式接线端子。该模块支持高密度 IO 模块。它具有 36 引脚，设计用于端接 14-26 AWG 之间的导体尺寸。IC694TBB132接线端子配有用于牢固连接的螺钉。接线端子尺寸紧凑，尺寸为6英寸长，6英寸宽。

IC694TBB132接线端子的外盖比内部深 0.5 英寸。这种设计有助于适应绝缘层较厚的电线。端子螺钉的拧紧扭矩为一英寸 7 磅。IC694TBB132接线端子使用底部作为电线条的量规。为了隔离，电线应完全插入接线端子。接线端子易于安装和更换。模块中的线束应保护在接线端子的底部。安装新块时，盖子的顶部和底部应对齐在一起，块内的凹口完全相同，并设有盖槽。在拆卸过程中，应将闩锁推到下方，直到松开块。

GE IC694TBB132 高密度扩展盒式接线端子

【英文介绍】

The IC694TBB132 is a 36-pin high-density expansion box terminal that can be used with the PACSystem RX32i Programmable Automation Controller (PAC) family and the equivalent 3-90 series PLC platform with 30 input I/O modules. The terminals are currently manufactured by Emerson Automation and were previously manufactured by GE Intelligent Platforms (GE IP). The IC694TBB132 has a standard depth output cover with a size of 23 mm or 0.9 inches. Terminals are designed to terminate #14-26 American Wire Gauge (AWG), solid or stranded copper wire in a range of wire sizes. The length of the ribbon end is 0.310 inches, which is 7.87 mm. The bottom of the terminal is designed to refer to the recommended wire length. The recommended tightening torque applied to each connection point is 7 lb-inch. To attach the IC694TBB132 box terminal to its cover, align the top of the terminal with the bottom of the cover. Check for grooves and grooves on cover plates and terminals. They must be aligned to ensure that the terminals fit perfectly into the module. Once aligned, slide the terminal up until you hear a click. If you feel resistance during insertion, do not insert the module forcefully, but pull it out and recheck the alignment and possible obstructions before trying again. Once installed with the cover, the component can now be connected to the main module. Align the component with the front panel port of the module. Press the terminal assembly vertically towards the module until it is in place. Open the front cover and push back the latch to lock the assembly in place.

The IC694TBB132 terminal is a boxed terminal produced by GE Fanuc. This module supports high-density I/O modules. It has 36 pins and is designed to terminate conductor sizes between 14-26 AWG. The IC694TBB132 terminals are equipped with screws for secure connection. The terminals are compact in size, 6 inches long and 6 inches wide.

The outer cover of the IC694TBB132 terminal is 0.5 inches deeper than the inside. This design helps to accommodate wires with thicker insulation. The tightening torque of the terminal screw is 7 pounds per inch. The IC694TBB132 terminal uses the bottom as the gauge of the electrical wire. For isolation, the wire should be fully inserted into the terminal. Terminals are easy to install and replace. The harness in the module should be protected at the bottom of the terminal. When installing a new block, the top and bottom of the cover should be aligned together, the notch in the block is exactly the same, and the cover groove is provided. During removal, the latch should be pushed down until the block is released.

GE IC694TBB132 高密度扩展盒式接线端子

【其他型号推荐】