IC694MDL916 单插槽模块 输出触点为干触点

【产品详情】

技术规格

额定电压： 5/24/125 伏直流电，120/240 伏交流电

# 输出数量： 16（隔离）

频率： 50/60Hz（仅限交流电）

输出电流： 每点最大 10mA

输出电压范围： 5 至 125VDC，5 至 250 VAC

功耗： 300mA （来自 5V 总线），150mA 来自 24V 继电器

IC694MDL916是十六 （16） 通道继电器输出模块，属于 PACSystem RX3i 产品系列。该模块是一个单插槽模块，以前由GE智能平台制造，现在由艾默生自动化制造。它带有单独隔离的 A 型或常开 （N.O.） 触点输出。

该模块的输出触点为干触点，允许每个通道传导交流和直流电压的任意组合。它支持 5-250VAC 范围的传导，标称值为 120-240 VAC，频率范围为 47-63 Hz。它还兼容 0-125 VDC 电压，标称电压水平为 5 / 24 / 125 VDC。每个输出触点的最小电流容量为每点 10 mA，而 200VDC 的最大额定值为 125mA（最大阻性）;每路输出 2A 导通负载（5 至 30VDC，5 至 250VAC）;每路输出 2A 灯负载（5 至 30VDC，5 至 250VAC）;4-5VDC 最大值（阻性）为 30A，最大 4-5VAC 负载为 250A（阻性或通用）。

GE Fanuc RX3i PACSystems IC694MDL916 16 点继电器输出模块使用外部电源，需要 0 至 250 伏交流电或 0 至 125 伏直流电的额定电源电压。其支持的输出电压范围为 5 至 250 伏交流电或 0 至 125 伏直流电，两个电压范围的频率范围均为 47 至 63 赫兹。IC694MDL916继电器输出模块的典型响应时间约为 10 毫秒，无论是在模块关闭时还是在打开时。该模块需要安装在将承载其所有接线的接线端子上，并且它与几种不同类型的接线端子兼容，包括标准弹簧和箱式接线端子以及加长弹簧和箱式接线端子。

IC694MDL916 单插槽模块 输出触点为干触点

【英文介绍】

Technical specification

Rated voltage: 5/24/125 VDC, 120/240 VAC

# Output quantity: 16 (isolated)

Frequency: 50/60Hz (AC only)

Output current: Maximum 10mA per point

Output voltage range: 5 to 125VDC, 5 to 250 VAC

Power consumption: 300mA (from 5V bus), 150mA from 24V relay

The IC694MDL916 is a sixteen (16) channel relay output module belonging to the PACSystem RX3i product family. The module is a single-slot module that was previously manufactured by GE Intelligent Platforms and is now manufactured by Emerson Automation. It comes with A separate isolated Type A or normally open (N.O.) contact output.

The module's output contacts are dry contacts, allowing each channel to conduct any combination of AC and DC voltages. It supports conduction in the range of 5-250VAC, nominal values of 120-240 VAC, and frequency range of 47-63 Hz. It is also compatible with 0-125 VDC voltages, with a nominal voltage level of 5/24/125 VDC. The minimum current capacity of each output contact is 10 mA per point, while the maximum rating of 200VDC is 125mA (maximum resistance); Each output 2A on-load (5 to 30VDC, 5 to 250VAC); Each output 2A lamp load (5 to 30VDC, 5 to 250VAC); The 4-5VDC maximum (resistive) is 30A, and the maximum 4-5VAC load is 250A (resistive or universal).

GE Fanuc RX3i PACSystems IC694MDL916 The 16-point relay output module uses an external power supply and requires a rated supply voltage of 0 to 250 volts AC or 0 to 125 volts DC. It supports an output voltage range of 5 to 250 volts AC or 0 to 125 volts DC, with a frequency range of 47 to 63 Hz for both voltage ranges. The typical response time of the IC694MDL916 relay output module is about 10 milliseconds, both when the module is off and when it is on. The module needs to be mounted on the terminal that will carry all of its wiring, and it is compatible with several different types of terminal, including standard spring and box terminals as well as extended spring and box terminals.

IC694MDL916 单插槽模块 输出触点为干触点

【其他型号推荐】