GE IC694BEM331 总线控制器模块 现场I / O控制站

【产品详情】

IC694BEM331是GE Fanuc / Emerson PACSystem RX3i Genius总线控制器模块。该模块主要用于允许RX3i机架与利用Genius总线的其他控制器平台进行通信。此类控制器平台可能包括VersaMax，Genius Block，Genius手持监视器（HHM），现场I / O控制站，远程或分布式I / O机架以及支持Genius总线的多个主机。 IC694BEM331支持与每个支持Genius的设备交换多达128字节的数据。

它还可以为每次总线扫描发送多达 128 字节的全局数据。每次完成总线扫描时，它还可以接收多达 128 字节的全局数据。单个 RX3i 系统最多可以支持八 （8） 个 Genius 总线控制器。

IC694BEM331有两 （2） 个 LED 状态指示灯。这些 LED 指示灯用于指示模块的运行和通信状态。正常操作期间，OK LED 自然激活。在诊断和上电期间，此指示灯熄灭。COM LED 描述了 Genius 总线之间的通信交换状态。正常运行时，COM 指示灯被激活。对于间歇性总线错误，COM LED 闪烁并完全关闭是 Genius 总线出现故障。此外，当 CPU 未从IC694BEM331总线控制器收到任何合格信息时，COM LED 不会激活。

IC694BEM331支持153.5K波特标准/扩展，76.8K波特或38.4K波特的传输速率，这是软件可配置的。所需的总线端接是电气总线电缆两端的 75、100、120 或 150 欧姆电阻。

GE 控制器的隔离额定值为 2000 V，隔离额定值为 1500 Vts 瞬态共模抑制。

GE Fanuc EX3i PacSystems IC694BEM331总线控制器使用 Proficy Machine Edition 软件进行配置。它的额定电流为 300 毫安。总线控制器的额定电压为 5 伏直流电。总线控制器具有先进的诊断功能，可以在PLC系统运行过程中查明不同的故障和错误。对于通信，控制器同时使用全局数据和数据报。IC694BEM331总线控制器尺寸紧凑，可轻松安装到整个PLC系统中。总线控制器IC694BEM331使用菊花链电缆或双绞线电缆。该控制器与GE系列90-30和系列6 PLC系统兼容。

IC694BEM331常见问题

GE Fanuc IC694BEM331 Genius 总线控制器连接 PACSystems RX3i 和 Genius I/O 串行总线。除了总线控制器外，总线还将提供：Genius Blocks，远程丢弃，VersaMax和现场控制I / O站，带有Genius Bus的PLC，Genius手持监视器（HHM）和众多主机。Genius I/O 总线上的每个设备具有 128 字节交换功能，Genius 模块和其他设备以自动方式报告故障，包括向总线控制器发出警报和某些其他先前定义的问题。然后，总线控制器管理它收到的任何诊断消息，然后由 CPU 例行读取这些消息。如果使用编程软件，则可以在故障表中显示故障。

该IC694BEM331维护所有Genius数据报，每次总线审查时最多可发送128字节的全局数据。全局数据是自发和机械广播的数据。系统中最多可包含八个Genius总线控制器，每个控制器最多可传输128个字节。

控制器前面的 LED 用于指定运行状态。菊花链式总线电缆具有先进的诊断功能，使用单根双绞线加屏蔽或 Twinax。但是，也可以使用光纤电缆和调制解调器。总线的最大长度为7800Kbaud时为4英尺，4500.76 Kbaud时为8英尺，3500.153 Kbaud时为6英尺，2000.153 Kbaud标准时为6英尺。除 32.38 Kbaud 外，该单元的最大设备数量在所有波特率下为 4 个，在 16.38 Kbaud 时为 4 个设备。该控制器非常适合多个系列，可以使用固件版本为3.1或更高版本的RX5i Genius总线控制器交换全局数据。用户应该知道模块上没有可用的手持显示器连接器，但手持显示器可以与控制器互连。

IC694BEM331控制器是由GE Fanuc Automation制造的Genius I / O总线控制器，是RX3i PACSystems产品线的成员。它旨在与 RX3i PACSystems 控制器以及串行总线 I/O 无缝连接。该控制器与各种模块、远程控制器、控制器、手持式监控设备和 I/O 站完美匹配并配合使用。IC694BEM331控制器允许在I/O总线上一次交换多达128个数据字节。此 Genius I/O 总线控制器正面有 2 个 LED 指示灯，用于显示操作状态和通信总线状态。当模块正常运行时，这两个 LED 指示灯变为绿色。它支持可配置的各种数据速率，例如，它带有2.153 Kbaud的速率，用于标准和扩展通信。该单元还具有约5.76 Kbaud和8.38 Kbaud的可能通信速率。

GE Fanuc RX4i PACSystems IC3BEM694 Genius I/O 总线控制器具有额定值为 331 欧姆、75 欧姆、100 欧姆和 120 欧姆的总线终端电阻，电阻位于电动总线电缆的两端。该 GE 总线控制器具有 150 V 的耐压隔离额定值，瞬态共模抑制额定值为 2000 V。GE Fanuc IC1500BEM694总线控制器单元通过Proficy机器版编程软件进行控制。它具有 331 毫安的额定电流，额定电压为 300 伏直流电。该装置还具有改进的诊断能力，并且可以在PLC系统运行时检测各种错误和故障。

GE IC694BEM331 总线控制器模块 现场I / O控制站

【英文介绍】

The IC694BEM331 is a GE Fanuc/Emerson PACSystem RX3i Genius bus controller module. This module is primarily used to allow the RX3i rack to communicate with other controller platforms that utilize the Genius bus. Such controller platforms may include VersaMax, Genius Block, Genius Handheld Monitor (HHM), field I/O control stations, remote or distributed I/O racks, and multiple hosts that support the Genius bus. The IC694BEM331 supports the exchange of up to 128 bytes of data with each Genius-enabled device.

It can also send up to 128 bytes of global data for each bus scan. It can also receive up to 128 bytes of global data each time a bus scan is completed. A single RX3i system can support up to eight (8) Genius bus controllers.

The IC694BEM331 has two (2) LED status indicators. These LED indicators are used to indicate the operating and communication status of the module. OK LED activates naturally during normal operation. This indicator is off during diagnosis and power-on. COM LED describes the status of communication exchange between Genius buses. During normal operation, the COM indicator is activated. For intermittent bus errors, COM LED flashing and completely off is Genius bus failure. In addition, the COM LED does not activate when the CPU does not receive any qualifying information from the IC694BEM331 bus controller.

The IC694BEM331 supports 153.5K baud standard/extended, 76.8K baud or 38.4K baud transfer rates, which are software configurable. The required bus terminations are 75, 100, 120, or 150 ohm resistors at both ends of the electrical bus cable.

The GE controller has an isolation rating of 2000 V and an isolation rating of 1500 Vts transient common mode rejection.

The GE Fanuc EX3i PacSystems IC694BEM331 bus controller is configured using Proficy Machine Edition software. It has a rated current of 300 mA. The bus controller is rated at 5 volts DC. The bus controller has advanced diagnostic functions, which can identify different faults and errors during the operation of the PLC system. For communication, the controller uses both global data and datagrams. The IC694BEM331 bus controller is compact in size and can be easily installed into the entire PLC system. The bus controller IC694BEM331 uses Daisy chain cables or twisted pair cables. The controller is compatible with GE Series 90-30 and Series 6 PLC systems.

IC694BEM331 Frequently Asked Questions

The GE Fanuc IC694BEM331 Genius Bus controller connects to the PACSystems RX3i and Genius I/O serial buses. In addition to the Bus controller, the bus will also be available: Genius Blocks, Remote Drop, VersaMax and field control I/O stations, PLCS with Genius Bus, Genius Handheld Monitor (HHM) and numerous hosts. Each device on the Genius I/O bus has 128 byte exchange capabilities, and Genius modules and other devices report faults in an automatic manner, including alerts to the bus controller and certain other previously defined problems. The bus controller then manages any diagnostic messages it receives, which are then read routinely by the CPU. If programming software is used, the fault can be displayed in the fault table.

The IC694BEM331 maintains all Genius datagrams and can send up to 128 bytes of global data per bus review. Global data is data that is spontaneously and mechanically broadcast. The system can contain up to eight Genius bus controllers, each of which can transfer up to 128 bytes.

The LED on the front of the controller is used to specify the operating state. Daisy-chain bus cables feature advanced diagnostic functions using a single twisted pair plus shielding or Twinax. However, fiber optic cables and modems can also be used. The maximum length of the bus is 4 feet at 7800Kbaud, 8 feet at 4500.76 Kbaud, 6 feet at 3500.153 Kbaud, and 6 feet at 2000.153 Kbaud standard. With the exception of 32.38 Kbaud, the maximum number of devices in this unit is 4 at all baud rates and 4 at 16.38 Kbaud. The controller is well suited for multiple families and can exchange global data using an RX5i Genius bus controller with firmware version 3.1 or higher. The user should be aware that there is no handheld display connector available on the module, but the handheld display can interconnect with the controller.

The IC694BEM331 controller is a Genius I/O bus controller manufactured by GE Fanuc Automation and is a member of the RX3i PACSystems product line. It is designed to seamlessly connect with RX3i PACSystems controllers as well as serial bus I/O. The controller works perfectly with a variety of modules, remote controllers, controllers, handheld monitoring devices and I/O stations. The IC694BEM331 controller allows up to 128 bytes of data to be exchanged at a time on the I/O bus. This Genius I/O bus controller has 2 LED indicators on the front to show the operating status and communication bus status. When the module is operating normally, these two LED indicators turn green. It supports a variety of configurable data rates, for example, it comes with a rate of 2.153 Kbaud for standard and extended communications. The unit also has a possible communication rate of approximately 5.76 Kbaud and 8.38 Kbaud.

GE Fanuc RX4i PACSystems IC3BEM694 Genius I/O bus controllers have bus terminal resistors rated 331 ohm, 75 ohm, 100 Ohm, and 120 Ohm, and the resistors are located at both ends of the motorized bus cable. The GE bus controller has a withstand voltage isolation rating of 150 V and transient common mode rejection rating of 2000 V. The GE Fanuc IC1500BEM694 bus controller unit is controlled by Proficy Machine Edition programming software. It has a current rating of 331 mA and a rated voltage of 300 volts DC. The unit also has improved diagnostic capabilities and can detect various errors and faults while the PLC system is running.

GE IC694BEM331 总线控制器模块 现场I / O控制站

【其他型号推荐】