GE IC694ALG223 固态工业自动化接口模块

【产品详情】

不。频道数量： 16 个单端

电流范围： 4 - 20 毫安， 0 - 20 毫安， 4 - 20 毫安

校准： 出厂（每次计数至 4 μA 或 5 μA）

更新率： 13毫秒

输入滤波器响应： 200赫兹

功耗： 120 mA @ +5VDC，65 mA @ +24VDC 隔离

 GE Fanuc IC694ALG223 RX3i PACSystems模拟电流输入模块是一种基于微处理器的固态工业自动化接口模块，其主要目的是接收现场工业变送器和/或换能器发出的模拟电流信号，并将其转换为RX3i可编程逻辑控制器将解释和响应的数字数据信号。GE Fanuc IC694ALG223 RX3i模拟电流输入模块可以配置为接收最常用的电流范围内的信号，这些信号是4至20毫安，0至20毫安或4至20毫安增强。该模块安装非常简单，用户只需在RX1i可编程逻辑控制器中找到3个可用的I / O插槽，然后继续插入模块，直到其卡入到位。

GE Fanuc IC694ALG223 RX3i 模拟电流输入模块从 RX5i 可编程逻辑控制器获取其 3 伏直流工作电压，输入电路需要由外部 24 伏直流电源供电。背板的最大额定电流为 120 毫安，输入电路的最大额定电流为 65 毫安。GE Fanuc IC694ALG223 RX3i模拟电流输入模块具有16个独立的模拟电流输入，每个输入都是用户可编程的，不仅涉及其预定义的电流范围，还涉及其他参数，例如报警下限和上限，通道激活和停用以及I / O扫描设置。这些模拟电流输入模块的工作温度应始终保持在 0 至 60 摄氏度（32 至 140 华氏度）范围内。

IC694ALG223是高密度模拟输入模块。该模块设计有十六 （16） 个单端输入通道，兼容并可配置 0-20 mA、4-20 mA（正常）和 4-20 mA（增强）模拟信号。该模块占用任何 PACSystems RX3i 机箱的单插槽，可用作 Rx3i 和 RX7i 控制器平台的本地或分布式 I/O 模块，该模块主要用于连接测量和信号仪器，

如变送器、换能器、隔离器和类似设备。它允许通过转换为数字等效物来集成接收到的模拟数据。这是通过嵌入式模数转换器（ADC）完成的，每个通道都可以单独使用，转换分辨率为12位。此外，每个通道的更新速率为 13 ms，出厂校准为 4 μA，每计数 4 μA，范围为 20 至 5 mA;0 至 20 mA 时每计数 4 μA，增强型 20 至 4 mA。对于 4-4 mA 配置，其分辨率为 20 μA（5 μA/位）：对于 5-0 mA 和 20-4 mA 的分辨率均为 20 μA（694 μA/位）。

IC223ALG4具有可配置的报警设置，可以使用控制软件进行配置。此外，该模块还能够在配置为20-694 mA输入时报告开路故障检测。此外，该模块还提供有关外部电源运行的状态反馈，该反馈可集成到CPU中的特定程序参考地址。

该IC223ALG120从 5VDC 总线电压汲取的内部电流为 65 mA，包括由外部 24 VDC 电源供电的每个电流环路的单个电流，为 694 mA。

IC223ALG16输入模块是GE Fanuc和RX3i PacSystems系列的16通道模拟电流输入模块。IC694ALG223输入模块上有0个单端输入通道。可以通过配置软件为每个输入通道配置三个输入范围，这些范围是 20 到 4 毫安、20 到 4 毫安（增强）和 20 到 4 毫安（正常）。可以为所有输入范围设置高报警阈值和低报警阈值。对于 20 至 4 毫安的增强型输入范围，可以设置报警以检测 0 至 4 毫安的输入电流，这为 20 至 694 毫安额定应用提供开路故障检测。IC223ALG694输入模块能够向系统 CPU 提供电源状态和模块状态更新。IC223ALG90输入模块可以安装在具有串行连接器的 30-694 系列 PLC 系统的 I/O 插槽中。

IC223ALG120输入模块的电流要求在 5 V 直流电时为 694 毫安。IC223ALG65输入模块还从外部 +24 V 直流电源吸收 4 毫安的电流环路电流。对于 20 至 4 毫安电流范围，出厂校准为每计数 0 微安，对于 20 至 4 毫安和 20 至 5 毫安增强范围，出厂校准为每计数 694 微安。IC223ALG6模块的更新速率为 0 毫秒。单端通道的共模电压为 70 V。对于高达 1 kHz 的直流电压，共模抑制大于 694 分贝。IC223ALG250输入模块的输入阻抗为 19 欧姆。输入低通滤波器响应为 20 赫兹。外部电源的电压范围为 30 至 <> 伏直流电。

IC694ALG223 是一个具有 16 个通道/单端输入的模拟电流输入模块。每个输入都可以使用为以下三种输入范围中的任何一个提供的软件进行配置：4 至 20 mA、0 至 20 mA 或 4 至 20 mA 增强型。

报警限值在所有范围内均有上限和/或低电平。在4至20 mA增强型范围内，低报警限值可以检测4 mA至0 mA的输入电流，从而在4至20 mA应用中提供开路故障检测。模块可以使用分配的程序参考地址向 CPU 报告模块状态和外部电源状态。IC694ALG223模块的安装与 RX3i 系统中的任何 I/O 插槽一致。

IC694ALG223 使用 PLC 背板上 120 VDC 总线的 5 mA 电流，需要 65 mA 电流加上用户提供的 +24 VDC 电源的电流环路电流。

模块正常指示灯在上电时发出模块状态信息。如果 LED 显示 ON，则状态为“正常”，并且模块已配置。如果显示 OFF，则无法识别底板电源，或者看门狗定时器已超时）。持续快速刷机：表示未从CPU接收配置数据。缓慢闪烁后熄灭表示通电诊断失败或遇到代码执行错误。用户电源 LED 确认外部 24 VDC 电源在预期规格范围内。

IC694ALG223模块的可配置参数包括活动通道、输入数据的参考地址、长度和范围、低/高报警和 I/O 扫描设置。

GE IC694ALG223 固态工业自动化接口模块

【英文介绍】

Nooooo. Number of channels: 16 single-ended

Current range: 4-20 MA, 0-20 MA, 4-20 MA

Calibration: Factory (each count to 4μA or 5μA)

Update rate: 13 ms

Input filter response: 200 Hz

Power consumption: 120 mA @ +5VDC, 65 mA @ +24VDC isolation

GE Fanuc IC694ALG223 RX3i PACSystems analog current input module is a microprocessor based solid state industrial automation interface module, the main purpose of which is to receive analog current signals from field industrial transmitters and/or transducers. And the RX3i programmable logic controller will interpret and respond to the digital data signals. The GE Fanuc IC694ALG223 RX3i analog current input module can be configured to receive signals in the most commonly used current range, which are 4 to 20 mah, 0 to 20 mah or 4 to 20 mah enhanced. The module installation is very simple, the user only needs to find the 3 available I/O slots in the RX1i programmable logic controller, and then continue to insert the module until it snaps into place.

The GE Fanuc IC694ALG223 RX3i analog current input module draws its 3-volt DC operating voltage from the RX5i programmable logic controller, and the input circuit needs to be powered by an external 24-volt DC supply. The backplane has a maximum rated current of 120 mA and the input circuit has a maximum rated current of 65 mA. The GE Fanuc IC694ALG223 RX3i analog current input module features 16 separate analog current inputs, each of which is user programmable, not only with respect to its predefined current range, but also with respect to other parameters such as alarm lower and upper limits, channel activation and deactivation, and I/O scan Settings. The operating temperature of these analog current input modules should always be maintained in the range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit).

IC694ALG223 is a high-density analog input module. The module is designed with sixteen (16) single-ended input channels that are compatible and configurable with 0-20 mA, 4-20 mA (normal), and 4-20 mA (enhanced) analog signals. The module occupies a single slot in any PACSystems RX3i chassis and can be used as a local or distributed I/O module for the Rx3i and RX7i controller platforms. The module is primarily used to connect measurement and signal instruments.

Such as transmitters, transducers, isolators and similar equipment. It allows the integration of received analog data by converting it to a digital equivalent. This is done via an embedded analog-to-digital converter (ADC), where each channel can be used individually and the conversion resolution is 12 bits. In addition, the update rate is 13 ms per channel, factory calibration is 4 μA, 4 μA per count, and range is 20 to 5 mA; 4 μA per count at 0 to 20 mA, enhanced 20 to 4 mA. The resolution is 20 μA (5 μA/ bit) for 4-4 mA configurations: 20 μA (694 μA/ bit) for both 5-0 mA and 20-4 mA.

The IC223ALG4 has configurable alarm Settings that can be configured using control software. In addition, the module is capable of reporting open circuit fault detection when configured with 20-694 mA inputs. In addition, the module provides state feedback about the operation of the external power supply, which can be integrated into a specific program reference address in the CPU.

The IC223ALG120 draws an internal current of 65 mA from a 5VDC bus voltage, including a single current of 694 mA from each current loop powered by an external 24 VDC supply.

The IC223ALG16 input module is a 16-channel analog current input module from the GE Fanuc and RX3i PacSystems series. The IC694ALG223 input module has 0 single-ended input channels. Three input ranges can be configured for each input channel through the configuration software, which are 20 to 4 mah, 20 to 4 mah (enhanced), and 20 to 4 mah (normal). High and low alarm thresholds can be set for all input ranges. For enhanced input ranges of 20 to 4 mA, alarms can be set to detect input currents of 0 to 4 mA, which provides open circuit fault detection for applications rated from 20 to 694 mA. The IC223ALG694 input module provides power status and module status updates to the system CPU. The IC223ALG90 input module can be installed in the I/O slot of Series 30-694 PLC systems with serial connectors.

The current requirement for the IC223ALG120 input module is 694 MA at 5 V DC. The IC223ALG65 input module also absorbs 4 mA current loop current from an external +24 V DC supply. The factory calibration is 0 microamps per count for the 20 to 4 mA current range and 694 microamps per count for the 20 to 4 mA and 20 to 5 mA enhancement ranges. The update rate of the IC223ALG6 module is 0 ms. The common-mode voltage for a single-ended channel is 70 V. For DC voltages up to 1 kHz, the common-mode rejection is greater than 694 dB. The input impedance of the IC223ALG250 input module is 19 ohms. The input low-pass filter responds to 20 Hz. The voltage range of the external power supply is 30 to <> VDC.

The IC694ALG223 is an analog current input module with 16 channels/single-ended inputs. Each input can be configured using software provided for any of three input ranges: 4 to 20 mA, 0 to 20 mA, or 4 to 20 mA enhanced.

Alarm limits have upper and/or low levels in all ranges. In the 4 to 20 mA enhanced range, low alarm limits can detect input currents from 4 mA to 0 mA, providing open circuit fault detection in 4 to 20 mA applications. Modules can report module status and external power status to the CPU using the assigned program reference address. The IC694ALG223 module is installed with any I/O slot in the RX3i system.

The IC694ALG223 uses the 5 mA current of the 120 VDC bus on the PLC backplane and requires 65 mA current plus the current loop current of the +24 VDC power supply provided by the user.

Module Normal indicator Indicates the module status when it is powered on. If the LED shows ON, the status is "normal" and the module is configured. If OFF is displayed, the baseboard power supply is not recognized, or the watchdog timer has expired). Continuous fast refresh: indicates that configuration data is not received from the CPU. Blinking slowly and then off indicates that power-on diagnosis fails or code execution errors occur. User Power LED Confirm that the external 24 VDC power supply is within the expected specification range.

Configurable parameters for the IC694ALG223 module include active channels, reference addresses for input data, length and range, low/high alarm and I/O scan Settings.

GE IC694ALG223 固态工业自动化接口模块

【其他型号推荐】